Xem giùm mình cái log c2-03 với.

MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 4], SN: C0803B22
Using device: USB ROM and HTI, FW ver: 00.50, SN: 000160E1
Connection status: UHCI:HUB::USB 1.10 (Full-speed)
Driver: NMWCD, ver: 7.1.32.75
Module ver: 1.0.0.20713(27-03-2012), Library ver: 1.0.0.13992(27-03-2012)
Make sure USB cable, Battery and charger are removed from device.
Insert USB cable, Battery back to device(make sure to have fully charged battery).
Insert Charger or Press phone's power button(if flashing doesnt start automatically)
Waiting for USB ROM device ...
Device synchronized.
CPU: XGOLD 213
Sending EBL Loader...OK
Sending EBL ...OK
Getting EBL Version ...
Boot mode: 0xCC
EBL version major/minor: 10.37
EBL version: Quantum_Bootloader_10.37_M1S1
Protocol version suggested by phone: 3
Set baud rate to: 6.50 Mbit/s
Flash ID: 0089 8982 - 23280001 [Intel NU48F512,512 Mbits]
CFI information:
Flash settings: 0/1024, size: 0x04000000
1 Block regions:
512 x 0x00020000 = 0x04000000
EBL ready !
Original IMEI:
RPL backup already exist (C:\mobileEx\3.5\data\backup\XGOLD__back.RPL)
Processing file: rm702__06.97.mcusw
Downloading item CODE:rm702__06.97.mcusw_ebl_psi.fls, num block: 4, size: 28 MB
Erasing area 0x40000000-0x4001FFFE ...OK
Programming completed in 0.344 s
Erasing area 0x40040000-0x4005FFFE ...OK
Programming completed in 0.328 s
Erasing area 0x40060000-0x4015FFFE ...OK
Programming ...
Task failed at (08000012)!!!
Last RX buffer: 00 00 00 00 00 00 00 00 00 00 00 00 CC 00 00 00 0A 00 00 00 25 00 00 00 51 75 61 6E 74 75 6D 5F 42 6F 6F 74 6C 6F 61 64 65 72 5F 31 30 2E 33 37 5F 4D 31 53 31 00 00 00 03 10 01 00 01 00 00 00 00 00 00 01 00 00 00 00 00 00 00 00 1F 00 00 00 00 00 00 00 00 00 00 00 02 08 00 00 02 00 00 00 98 45 80 60 40 45 80 60 01 00 00 00 0B 00 00 00 64 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Lên trắng mh rồi đứng yên luôn

đưa qua phoenix xem sao bác

Đưa qua ATF thì nó báo

Number of Image Files: 3

Processing Image File :
rm702__06.97.mcusw
Processing Image File :
rm702__06.97.ppm_v
Processing Image File :
rm702__06.97.image_v_059L5S8


AUTO SELECTED DEAD USB FLASHING...

If Phone Booting does not Start in 5 Seconds,
Then Perform Steps 1, 2, 3 and 4...

1. Remove USB and Battery...
2. Insert USB.
3. Insert Battery. (Some phones boot automatically)
4. Please Power on phone shortly...


Infineon USB Boot: F00A1FB300020303010100FF
Sending PBL...
PBL Successfully Sent...
Sending SBL...
ERROR: SBL was NOT Accepted

Chạy bằng phoenix thì nó báo vậy

Flashing started
Creating product data items list
Product data items list created
Backup not required
Flashing phone
Initializing
Download files list initiated
Waiting for USB device...
Booting...
Sending EBL loader...
Sending EBL...
Boot failure (0x8401F185)
Failed to boot device
Flash operation failed
Starting to recover the phone
Recovering phone
Initializing
Download files list initiated

bạn nap ver cao nhất thử hoi sang mình bị 1 cây như thế minh la c2-00 nap nhầm c2-03 len trang treo nap lại c2-00 len bt.
nạp 3 4 lần mới ok không dc thì hwk 1 phát done

Đã ok rồi. Đóng lại 2 em flash va cpu. Đập băng mxbox 1 phát ok và đây là log của em nó

Insert Charger or Press phone's power button(if flashing doesnt start automatically)
Waiting for USB ROM device ...
Device synchronized.
CPU: XGOLD 213
Sending EBL Loader...OK
Sending EBL ...OK
Getting EBL Version ...
Boot mode: 0xCC
EBL version major/minor: 10.37
EBL version: Quantum_Bootloader_10.37_M1S1
Protocol version suggested by phone: 3
Set baud rate to: 6.50 Mbit/s
Flash ID: 0089 8982 - 23280001 [Intel NU48F512,512 Mbits]
CFI information:
Flash settings: 0/1024, size: 0x04000000
1 Block regions:
512 x 0x00020000 = 0x04000000
EBL ready !
Original IMEI:
RPL backup already exist (C:\mobileEx\3.5\data\backup\XGOLD__back.RPL)
Processing file: rm702__06.97.mcusw
Downloading item CODE:rm702__06.97.mcusw_ebl_psi.fls, num block: 4, size: 28 MB
Erasing area 0x40000000-0x4001FFFE ...OK
Programming completed in 0.343 s
Erasing area 0x40040000-0x4005FFFE ...OK
Programming completed in 0.344 s
Erasing area 0x40060000-0x4015FFFE ...OK
Programming completed in 1.360 s
Erasing area 0x40280000-0x41D3FFFE ...OK
Programming completed in 32.281 s
Checksum verified (0xA701)
Processing file: rm702__06.97.ppm_v
Downloading item CUST:package_v.ppm_ebl_psi.fls, num block: 1, size: 5.26 MB
Erasing area 0x41DC0000-0x42300772 ...OK
Programming completed in 6.469 s
Checksum verified (0x5007)
Processing file: rm702__06.97.image_v_059L5S8
Downloading item CUST:package_v_059L5S8.image.fls, num block: 1, size: 11.88 MB
Erasing area 0x424C0000-0x43E1FFFE ...OK
Programming completed in 14.453 s
Checksum verified (0xCB72)
Total time for flashing process(boot+erase+write) was 7 min 37.515 s
Waiting for USB device removal ...OK
Waiting for USB device arrival ...
Waiting for device boot up ...
Device connected: nmwcdc\Nokia C2-03 USB Phonet, PORT_ID: 33ED7359
Verifying communication to device OK.



Phone type: RM-702 (C2-03)
SW version: V 06.97 20-09-11 RM-702 (c) Nokia
Imei plain: 35906404727068-4
Product code: 059D3X0
Language Pack:
- not available.

SLPA ver[4]: PA_SL3/PA_SIMLOC30 (15 digit NCK)
warning: avoid SW Downgrade & manual erase to this phone !
Camera config: 06150123007025, ver:

Imei net: 35906404727068
Version: SIMLOCK SERVER
Provider: GSM Test Operator
Counter: 0/3, 0/10

CONFIG_DATA: 0010100000000000
PROFILE_BITS: 800000000003000B

BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN

Ghê vậy làm CPU luôn....http://vietfones.vn/forum/images/smilies/tutu.gif

chúc mừng đã có lúa

simlock bình thường...

bạn chạy ver cao nhất coi 7.63 luôn sao chạy ver thấp vậy