Được post bởi
binhokls
Backup already exists(D:\3.5\data\backup\XGOLD_RM-647_3BE61C556C495B3E_IMEI.back)
MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 3], SN: C0860294
Using device: HTI, FW ver: 00.50, SN: 0000C47F
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.0.0
Module ver: 1.0.0.19798(05-01-2012), Library ver: 1.0.0.13703(05-01-2012)
Do not disconnect or abort this operation otherwise phone will be damaged.
Device synchronized.
CPU: XGOLD 110
Using embedded SBL from MCU.
Sending EBL Loader ...OK
Sending EBL ...OK
Getting EBL Version ...
Boot mode: 0xCC
EBL version major/minor: 10.19
EBL version : Default_RAM_Bootloader
Set baud rate to: 921.60 Kbit/s
Flash ID: 0020 88C0 [ST M58MWR064FU,64 Mbits]
Processing file: rm647_006.500
Downloading item CODE:hw_b2_rm647_r06.500.fls, num block: 3, size: 4.04 MB
Erasing area 0x00800000-0x00A0FFFE ...OK
Programming completed in 39.813 s
Erasing area 0x00C60000-0x00E5933E ...OK
Programming completed in 39.547 s
Erasing area 0x00FFC000-0x00FFC03E ...OK
Programming completed in 0.250 s
Error reading checksum!
Processing file: rm647_006.50mr
Downloading item CUST:hw_b2_rm647_006.50mr.fls, num block: 1, size: 1.10 MB
Erasing area 0x00210000-0x003288BE ...OK
Programming completed in 18.938 s
Checksum mismatch: Phone calculated 0x0033, software calculated 0x52F7
Processing file: rm6470_nai06.50mr
Downloading item CUST:hw_b2_rm6470_nai06.50mr.fls, num block: 1, size: 305.83 KB
Erasing area 0x00EB0000-0x00EFBA3E ...OK
Programming completed in 5.250 s
Checksum mismatch: Phone calculated 0x00F0, software calculated 0x342D
Total time for flashing process(boot+erase+write) was 3 min 2.093 s
Phone type: RM-647
SW version: V 06.50 20-04-11 RM-647 (c) Nokia
Imei plain: 35974804667050-2
Product code: 0593142
Cellular system: GSM
ASIC ID: 0x2292, type: 11
Ppm Id: MR
Language Pack:
English,Hindi,Bengali
Imei net: 35974804667050
Provider: GSM Test Operator
Counter: 0/3, 0/10
CONFIG_DATA: 0010100000000000
PROFILE_BITS: 0000000000030002
BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
FULL FACTORY... OK
USER DATA... OK
LEAVE FACTORY... OK
SERVICE CENTER... OK
SOFTWARE UPGRADE... OK
PRODUCTION TUNING... OK
Reset User Code (to default:12345) ... OK
Completed in 2.078 s
