Xem hộ em cái log này với

MXKEY [MxKey Team HTI PLUS Flasher Interface 1], SN: C086FDF3
Using device: HTI, FW ver: 00.50, SN: 01006B97
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0
Module ver: 1.0.0.21200(18-07-2012), Library ver: 1.0.0.14214(25-10-2012)
Device synchronized.
CPU: XGOLD 110
Using embedded SBL from MCU.
Sending EBL Loader ...OK
Sending EBL ...OK
Getting EBL Version ...
Boot mode: 0xCC
EBL version major/minor: 10.19
EBL version: Default_RAM_Bootloader
Set baud rate to: 921.60 Kbit/s
Flash ID: 0020 88C0 - 23280003 [ST M58MWR064FU,64 Mbits]
CFI information:
Flash settings: 0/1, size: 0x00800000
2 Block regions:
127 x 0x00010000 = 0x007F0000
8 x 0x00002000 = 0x00010000
EBL ready !

đến đây là không check được nữa . các bác giúp em với

mang sang hwk chech thử rồi tung cái log nen anh em xem sao

chọn MCU , đánh dấu tick vào xGold . rồi check .hợac Flash luôn

MXKEY [MxKey Team HTI PLUS Flasher Interface 1], SN: C086FDF3
Using device: HTI, FW ver: 00.50, SN: 01006B97
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0
Module ver: 1.0.0.21200(18-07-2012), Library ver: 1.0.0.14214(25-10-2012)
Device synchronized.
CPU: XGOLD 110
Using embedded SBL from MCU.
Sending EBL Loader ...OK
Sending EBL ...OK
Getting EBL Version ...
Boot mode: 0xCC
EBL version major/minor: 10.19
EBL version: Default_RAM_Bootloader
Set baud rate to: 921.60 Kbit/s
Flash ID: 0020 88C0 - 23280003 [ST M58MWR064FU,64 Mbits]
CFI information:
Flash settings: 0/1, size: 0x00800000
2 Block regions:
127 x 0x00010000 = 0x007F0000
8 x 0x00002000 = 0x00010000
EBL ready !
Processing file: rm647_006.200
Downloading item CODE:hw_b2_rm647_r06.200.fls, num block: 3, size: 3.99 MB
Erasing area 0x00800000-0x00A0FFFE ...OK
Programming completed in 37.812 s
Erasing area 0x00C60000-0x00E4D5BE ...OK
Programming completed in 37.203 s
Erasing area 0x00FFC000-0x00FFC03E ...OK
Programming completed in 0.156 s
Checksum mismatch: Phone calculated 0xC88D, software calculated 0x2602
Total time for flashing process(boot+erase+write) was 2 min 14.797 s

chay lai luôn di chờ gì nửa ban

chạy rồi nhưng báo lỗi không được anh ơi /????

MXKEY [MxKey Team HTI PLUS Flasher Interface 1], SN: C086FDF3
Using device: HTI, FW ver: 00.50, SN: 01006B97
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0
Module ver: 1.0.0.21200(18-07-2012), Library ver: 1.0.0.14214(25-10-2012)
Device synchronized.
CPU: XGOLD 110
Using embedded SBL from MCU.
Sending EBL Loader ...OK
Sending EBL ...OK
Getting EBL Version ...
Boot mode: 0xCC
EBL version major/minor: 10.19
EBL version: Default_RAM_Bootloader
Set baud rate to: 921.60 Kbit/s
Flash ID: 0020 88C0 - 23280003 [ST M58MWR064FU,64 Mbits]
CFI information:
Flash settings: 0/1, size: 0x00800000
2 Block regions:
127 x 0x00010000 = 0x007F0000
8 x 0x00002000 = 0x00010000
EBL ready !
Processing file: rm647_006.200
Downloading item CODE:hw_b2_rm647_r06.200.fls, num block: 3, size: 3.99 MB
Erasing area 0x00800000-0x00A0FFFE ...OK
Programming completed in 39.969 s
Erasing area 0x00C60000-0x00E4D5BE ...OK
Programming completed in 37.360 s
Erasing area 0x00FFC000-0x00FFC03E ...OK
Programming completed in 0.156 s
Checksum mismatch: Phone calculated 0x943D, software calculated 0x2602
Processing file: rm647_006.20mr
Downloading item CUST:hw_b2_rm647_006.20mr.fls, num block: 1, size: 1.10 MB
Erasing area 0x00210000-0x003288BE ...OK
Programming completed in 21.328 s
Checksum mismatch: Phone calculated 0xC515, software calculated 0xB874
Processing file: rm6470_nai06.20mr
Downloading item CUST:hw_b2_rm6470_nai06.20mr.fls, num block: 1, size: 305.83 KB
Erasing area 0x00EB0000-0x00EFBA3E ...OK
Programming completed in 5.859 s
Checksum mismatch: Phone calculated 0xA596, software calculated 0xD819
Total time for flashing process(boot+erase+write) was 3 min 1.812 s

Em chạy song nó đến đây là dừng luôn :(

có bác nào giúp Em với .

mang ra tiệm đi bạn !

ông đọc mà không hiểu ak` ? khùng

máy bệnh gì sao không nói rỏ để ae giúp ...?
giờ làm chân lại cặp rồi flash lại coi có ok không ?

Em làm rồi nhưng vẫn not oke . flash đến đấy là dừng luôn . chán quá ?

vay thì thay cap đi là ok nhé

đã làm hết not oke . thay cpu oke / thank anh em đã quan tâm .:D