Giải mã 1 số lõi khi sử dụng JAF
________________________________________
Giúp anh em mới vào nghề khi sử dụng box JAF
mcuid AAAA - phone don't power on or don't signal TX high after power on ( Possible UPP damage, phone tx not making contact)
mcuid CCCC - phone don't signal TX high after UEM reset request (bsi line not connected properly, check for 3.3k resistor on bsi line, or UEM dmaged)
mcuid DDDD - phone don't signal TX low after UEM reset request ( usualy UEM damaged, or old jaf pcb until customer id 85xxxxxx must put a 33 pico capacitor b/w mbus-gnd)
mcuid EEEE - UPP don't respond to flash request routine.
Mcuid FFFF - cable problem. you must put an 3.3k resistor serial with bsi line and an 68k between GND and bsi
Error loading boot - Possible problems (RAM, UPP)
Error loading loader - Possible problems(RAM,UPP, FLASH CHIP), when you flash ape phones check for dku-2 usb cable.
error loading aditional loader - BT chip problems (skip BT may solve flashing problem)
Error erase - flash chip problem
Error cmd20 - BT chip problem
Error cmd14 - flash chip problem or old jaf pcb until customer id 85xxxxxx must put a 33 pico capacitor b/w mbus-gnd
When phone don't get into local mode always check for 68k resistor bsi-gnd
Có gì sai xót mong anh em góp ý thêm.Thanks
mình dịch ra tiếng viêt rồi nè
Trích:
Được post bởi
hoangthach
________________________________________
Giúp anh em mới vào nghề khi sử dụng box JAF
mcuid AAAA - phone don't power on or don't signal TX high after power on ( Possible UPP damage, phone tx not making contact)
mcuid CCCC - phone don't signal TX high after UEM reset request (bsi line not connected properly, check for 3.3k resistor on bsi line, or UEM dmaged)
mcuid DDDD - phone don't signal TX low after UEM reset request ( usualy UEM damaged, or old jaf pcb until customer id 85xxxxxx must put a 33 pico capacitor b/w mbus-gnd)
mcuid EEEE - UPP don't respond to flash request routine.
Mcuid FFFF - cable problem. you must put an 3.3k resistor serial with bsi line and an 68k between GND and bsi
Error loading boot - Possible problems (RAM, UPP)
Error loading loader - Possible problems(RAM,UPP, FLASH CHIP), when you flash ape phones check for dku-2 usb cable.
error loading aditional loader - BT chip problems (skip BT may solve flashing problem)
Error erase - flash chip problem
Error cmd20 - BT chip problem
Error cmd14 - flash chip problem or old jaf pcb until customer id 85xxxxxx must put a 33 pico capacitor b/w mbus-gnd
When phone don't get into local mode always check for 68k resistor bsi-gnd
Có gì sai xót mong anh em góp ý thêm.Thanks
mcuid CCCC - điện thoại không tín hiệu TX cao sau khi thiết lập lại yêu cầu UEM (bsi dòng không được kết nối đúng cách, kiểm tra cho 3.3k resistor trên bsi dòng, hoặc UEM dmaged)
mcuid àåäá - điện thoại không quyền lực vào ngày hoặc không tín hiệu TX cao sau khi mở điện (Possible Lên trên thiệt hại, điện thoại tx không làm liên lạc)
mcuid EEEE - Lên trên không đáp ứng với yêu cầu flash thông thường.
mcuid DDDD - điện thoại không tín hiệu TX thấp sau khi yêu cầu đặt lại UEM (thường UEM bị hư hỏng, hoặc cũ jaf PCB cho đến khi khách hàng id 85xxxxxx phải đặt một 33 pico Capacitor b / w mbus-gnd)
Mcuid FFFF - vấn đề cáp. bạn cần phải đặt một 3.3k resistor nối tiếp với dòng bsi và một 68k giữa GND và bsi
Lỗi tải khởi động - Có thể vấn đề (RAM, Lên trên)
lỗi tải aditional tải - BT chip vấn đề (bỏ qua BT có thể quyết vấn đề chớp)
Lỗi tải loader - Possible vấn đề (RAM, Lên trên, FLASH CHIP), khi bạn flash ape điện thoại kiểm tra cho DKU-2 cáp USB.
Lỗi xoá - flash chip vấn đề
Lỗi cmd20 - BT chip vấn đề
Lỗi cmd14 - flash chip giải quyết vấn đề hoặc old jaf PCB cho đến khi khách hàng id 85xxxxxx phải đặt một 33 pico Capacitor b / w mbus-gnd
Khi không nhận được điện thoại vào chế độ địa phương luôn luôn kiểm tra cho 68k resistor bsi-gnd
Dịch bằng Vdict còn một số điểm hoi khó hiểu các ban chịu khó nghiến cu nha :D