1202 cần giúp

1202 rớt nước khách bỏ pin vào sài một hồi ngủ luôn.em kẹp nguồn ko có dao động.em chà sấy kỹ ,bóc nguồn+cu+flash .rồi em nạp lại phân mềm thì nó báo vậy?
Detected PKEY: 9002CF36
Card life counter: 77.87%
P-key nokia module version 01.02
Detected JAF INTERFACE version: 01.B1, Driver version: 40000, Library version: 30107
JAF DCT4/BB5 LOADERS DIR: C:\Program Files\ODEON\JAF\Flash\
JAF DCT4/BB5 PRODUCT DIR: C:\Program Files\Nokia\Phoenix\Products\
JAF USB LOADERS DIR: C:\Program Files\ODEON\JAF\FlashUSB\
JAF DCT3/DCTL LOADERS DIR: C:\Program Files\ODEON\JAF\Flash3\
USB Cable Driver version: 7.0.2.0
Changing mode...Done!
FILES SET FOR FLASHING:
MCU Flash file: NONE
PPM Flash file: NONE
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Checking path: C:\Program Files\Nokia\Phoenix\Products\RH-112\

Searching for default location of ini...
Checking path: \Products\RH-112\
Searching for JAF saved location of ini...
Checking path: C:\Program Files\Nokia\Phoenix\Products\RH-112\
No ini files found...
FILES SET FOR FLASHING:
MCU Flash file: NONE
PPM Flash file: NONE
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: D:\PHAI NOKIA\phai nokia\rh-112\1202_RH-112_sw03.10ppmMR\rh112_003.100
PPM Flash file: NONE
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: D:\PHAI NOKIA\phai nokia\rh-112\1202_RH-112_sw03.10ppmMR\rh112_003.100
PPM Flash file: D:\PHAI NOKIA\phai nokia\rh-112\1202_RH-112_sw03.10ppmMR\rh112_003.10mr
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: D:\PHAI NOKIA\phai nokia\rh-112\1202_RH-112_sw03.10ppmMR\rh112_003.100
PPM Flash file: D:\PHAI NOKIA\phai nokia\rh-112\1202_RH-112_sw03.10ppmMR\rh112_003.10mr
CNT Flash file: D:\PHAI NOKIA\phai nokia\rh-112\1202_RH-112_sw03.10ppmMR\rh1120_nai03.10mr
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
MCU: D:\PHAI NOKIA\phai nokia\rh-112\1202_RH-112_sw03.10ppmMR\rh112_003.100
Booting phone...
Phone didn't answer with TX line low after UEM reset!
Causes:
1. put a 27-33 pico capacitor in connector b/w mbus-gnd.
2. UEM damaged -> replace uem.
MCU ID: 0xDDDD
This MCU ID is not supported in chosen flash file...
Error booting phone...
MCU: D:\PHAI NOKIA\phai nokia\rh-112\1202_RH-112_sw03.10ppmMR\rh112_003.100
Booting phone...
Phone didn't answer with TX line low after UEM reset!
Causes:
1. put a 27-33 pico capacitor in connector b/w mbus-gnd.
2. UEM damaged -> replace uem.
MCU ID: 0xDDDD
This MCU ID is not supported in chosen flash file...
Error booting phone...
MCU: D:\PHAI NOKIA\phai nokia\rh-112\1202_RH-112_sw03.10ppmMR\rh112_003.100
Booting phone...
MCU ID: 0xFFFF
This MCU ID is not supported in chosen flash file...
Error booting phone...
MCU: D:\PHAI NOKIA\phai nokia\rh-112\1202_RH-112_sw03.10ppmMR\rh112_003.100
Booting phone...
Phone didn't answer with TX line low after UEM reset!
Causes:
1. put a 27-33 pico capacitor in connector b/w mbus-gnd.
2. UEM damaged -> replace uem.
MCU ID: 0xDDD
This MCU ID is not supported in chosen flash file...
Error booting phone...
em thay .cpu+nguồn nó cũng báo như vậy.mong anh em nhiệt tình cứ giúp

anh em đâu cả rồi giúp em với 1202 này em chưa làm lần nào khó hiểu wua!!!!!!!!

trả con nguồn củ lại nạp lại
không nên xóa full nhe anh

Thay UPP 1200 vào chạy đ anh

làm lại chân cpu va nguồn chạy lại coi sao

lỗi CPU rồi nó không supost dc với con Flsah kìa, kiếm con khác thay thử xem