Video hướng dẫn chạy mcn-pro
McnPro - Pinouts Detection Procedure - A Quick Scan Guide
----------------------
Quick scan RX ,TX
----------------------
- Txd Rxd Gnd and Api(sky cpu) Pinout Scan
- Supports MTK TI ADI INF SKY AGE OM SPD...
- Takes just a few seconds
Step by Step:
* Connect McnPro to computer and open the main software
* Connect the phone with the right cable via USB etc.
* Use our special cable to connect phone to Negative / Positive, Box can automatic identification and that already have Protection System, so don't worry about the polarity.
* Press [Scan Rx Tx]
* If you already know the based cpu in phone, just select the related one (will be fast), otherwise select "Auto" (will take a few more seconds than usuall)
* Hold power-on button of your phone and press start button on the software interface , in just a few second you will get results ,eg.
Quote:
Scanning results:
GND: 12 13 ,RXD 10, TXD 15
Quote:
Scanning results:
Spd chipset
GND: 12 13 ,RXD 10, TXD 15, Boot:6
Quote:
API Scanning results:
API Pin 4-5
* You can save the scan results , because you might need that for the flash process
* BTW, for SKY cpu it's a little be different, Api can be detected and phone can be Reset. IMEI can be change too. (plz follow the window step by step procedure, its very easy.) eg.
Quote:
Scanning results:
SKY chipset
GND: 12 13 ,RXD 10, TXD 15
Scanning API pin(Please waiting...)
>>.......
API Scanning results:
API pin 5-6
Quote:
....
Connect ok
Modify imei...
Modify successful !
----------------------
USB Scan
----------------------
- Charge / Boot pin ,USBD+/-
- Supports MTK TI ADI INF SKY AGE OM SPD...
- Will take more seconds than above step
Step by Step:
* Connect McnPro to computer and open the main software
* Connect the phone with the right cable via USB etc.
* Use our special cable to connect phone to Negative / Positive, Box can automatic identification and that already have Protection System, so don't worry about the polarity.
* Press [USB Scan]
* In select option choose the same cable which you used, Eg. Mcnpro-11
* Hold power-on of your phone and press [Read starts] button on the software interface .eg.
Quote:
...
Scanning pin-status, please waiting..
->...............................
9,10 short-pin
>>Pin-status scanning completed
* Press [Charge-pin] button Box will be start to analyzing ,then follow the window step by step to do the procedure.when computer find a new USB device which mean's all step done. eg.
Quote:
...
USB D-:8 USB D+: 7 VCC:1 GND: 6 11
...
If scan other phone ,please press [stop]
How to Safely Read Lock Code with McnPro Box >>
1 - Connect your McnPro Box, then connect the right cable. Select Boot Version (Applies to some phones), Press Scan, then Select CPU Type and Start.
http://img7.imageshack.us/img7/3664/1mcnproteamr.jpg
2 - Pinouts are Automatically Detected & Applied by McnPro Software.
http://img10.imageshack.us/img10/3901/2mcnproteam.jpg
3 - Press the Unlock Button & wait. CPU Type is detected then Unlock Code is Read.
http://img12.imageshack.us/img12/9808/3mcnproteam.jpg
Enjoy McnPro's Easy to use software, with best Support.
Without USB connector how to flash /unlock phone with Mcnpro Box
Cutomer report if Phone without USB connector how to flash /unlock with Mcnpro box .
Here is the step :
1. Don't need to open phone , just check the T/P on the phone , normal beside the SIM card holder or under ticket .
2. Use universal Fbus cable (Nokia) or direct solder the cable on the T/P detect the PINOUT...
( If via universal Fbus cable you need use the service RJ45 Port )
3. Usually those kindly phone have 4 or 5 TP.
4. Select the related cable ,eg. C5T...
5. Then you can doing the things which you wanted .
Enjoy
Logs for phone AUX M822 :
Code:
Please Hold "ON" to connect with the phone...
Connected to Phone.
CPU：6205 Ver: 8B00 SW:8B00
CPU ID：
Downloading Boot...
Nor Flash Type: [SPANSION] S71GL032R4B
Nor Flash Code: 0001227E(221A2200)
Nor Flash Size: 0x00400000 Hex Bytes
INT/EXT RAM Size: 0x00008000+0x00100000
Verifying Baud...
Set Baud:921600 OK.
Reading(Nor)...
Read OK.
>>total： 3 mins17 s
Good Luck !
Step by Step HOW TO USE MCNpro Box (Details with Picture)
I.Instalation main software McnPro Box
1.Double click on the setup Mcnpro to start the installation 2.7.6a for main software box MCNpro.For update installer McnPro Box just visit here
http://i47.tinypic.com/2s1uq9z.jpg
2.Click Next to continue the installation process
http://i47.tinypic.com/33w8ker.jpg
3.in *******r Information, please insert the activation code same with listed in the your MCNprobox
http://i48.tinypic.com/ad154.jpg
4.In select Installation Folder just click Next To instal in this Folder
http://i48.tinypic.com/15jal1.jpg
5.Click Instal for begin installation main software McnPro Box
http://i49.tinypic.com/zmmdle.jpg
6.Please waiting process and then click Finish for the end of installation
http://i46.tinypic.com/2dwey3l.jpg
Tutorial For McnPro Box (For Mcnpro Box user)
Hướng dẫn chạy chip spetrum bằng mcn-pro
Anh em nào cần thì load về xem nhé
Hướng dẫn chạy dòng spetrum
mod ơi box này flash co good hơn spideman lắm không?
pro nào đã flash qua xin cho ý kiến .vì em cũng mún mua box mà chưa bít chọn box nào?xin ý kiến.thank...:p:p:p:p
