-
RIFF JTAG – RIFF JTAG Manager v1.24, RIFF Box Firmware v1.18 released
10.02.2011 RIFF JTAG Manager v1.24, RIFF Box Firmware v1.18
Firmware 1.18
---------------------------
- PXA270 debug is now available in ARM/Thumb modes (use the GDBServer for this);
JTAG Manager 1.24
---------------------------
- In case when Resurrector has no DCC Loader the JTAG Manager will now report it correctly and will not allow DCC Read/Write features
- (SDK): more functions are now available (exported) for future Resurrector DLLs;
- Usefull Plugins Enabled
---------------------------
Qualcom FullFlash Image Processing Tool:
This plugin works with NAND image files which have generic Qualcomm layout
With help of this plugin you can do:
- Disassemble a full NAND image file previously obtained with JTAG Manager (DCC Read/Write Page);
- Inspect each partition contents (main zone and spare zone) simultaneously;
- Save separate partitions to HDD (only main zone, only spare zone, or both zones);
- Write a chosen partition directly into phone;
- Read a chosen partition directly from the phone and substitute old partition contents to new ones;
Please note, direct read/write operations from/to the phone will require proper resurrector to be set (Resurrector Settings: thus before clicking the Activate Plugin button make sure compatible model is selected as well as other settings like TCK/RTCK frequencies).
You can access it from "Usefull Plugins" TAB.
-
16.02.2011 HTC HD7 Unbrick, Unlock, IMEI Repair and CID Update supported
16.02.2011 HTC HD7 Unbrick, Unlock, IMEI Repair and CID Update supported
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“HTC_HD7.dll” contains pinout, instructions and required repair files for HTC HD7 Unbrick, Unlock, IMEI Repair and CID Update.
http://www.jtagbox.com/wp-content/up.../htc_hd7_2.jpg
-
RIFF JTAG - HTC P3300 (HTC ARTE100, ARTE110) Unbrick - Boot Repair Supported
18.02.2011 HTC P3300 (HTC Artemis 100) Unbrick – Boot Repair Supported
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“HTC_Artemis.dll” contains pinout, instructions and required repair files for HTC P3300 (HTC Artemis 100) Unbrick – Boot Repair.
- Important :
There are 7 devices with Artemis code name. Check Your phone back sticker, if You see "ARTE100" or "ARTE110" You can repair Your phone.
"ARTE200" is NOT tested !.
RIFF Box – JTAG Revolution
-
RIFF JTAG - Updates
04.03.2011 Qualcom Generic NAND ESM7xxx DLL released
Resurrector ESM7XXX L41 D04 contains only DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager.
Embedded DCC Loader is designed to work inside of MCU's internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.
Initial H/W init sequence will setup MCU's PLL0 with these parameters:
* L/M/N = 0x41/0x00/0x01;
* Global Clock Divisor = DIV4
If you don't know what the L, M, N or Global Clock Divisor parameters are, then just keep in mind:
* Highest L values and lowest Global Clock Divisor values will make maximum clocking frequency supplied to the MCU's core and thus DCC Read/Write speed will be maximum fast;
* Too high frequency supplied to the MCU's core may result in core overheating or instable operation;
..................
04.03.2011 Samsung G800 Unbrick, dead boot repair supported
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“Samsung_G800.dll” contains pinout, instructions and required repair files for Samsung G800 Unbrick, dead boot repair.
..................
03.03.2011 ZTE MF180S Broadband modem Unbrick/Repair supported
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“ZTE_MF180S.dll” contains pinout, instructions and required repair files for ZTE MF180S Broadband modem Unbrick/Repair boot.
.................
RIFF Box – JTAG Revolution
-
RIFF JTAG - Updates from Yesterday :D
10.03.2011 HTC Tattoo A3232 (HTC Click 1100) Unlock, Unbrick, IMEI repair, CID Update supported
Resurrecting HTC Click is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inside.
There are two different hardware versions exist – one based on the MSM7225 chipset (CLIC10000) and other – on the ESM7225 chipset (CLIC11000). In resurrector settings you can select a desired version.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.52.0001 SPL version.
As well, you can change CID – for this make sure ‘Repair Custom ID’ field is checked in the Resurrection Guide dialog.
To resurrect HTC Click:
* Solder JTAG cable to HTC Click JTAG pads;
* Make sure HTC Click is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To Unlock HTC Click :
* Solder JTAG cable to HTC Click JTAG pads;
* Make sure HTC Click is selected in the list of models;
* Click Resurrect button;
* Select “Unlock Settings” TAB
* Select Unlock method
* Click “Unlock”
10.03.2011 HTC Desire DLL Update – Unlock Code reading supported
New HTC Desire DLL has additional option to select between reading NCK Code, or direct unlock.
This should also solve “error 0×45″ problem with some of the HW revisions.
10.03.2011 ASUS P526 Unbrick, Dead Boot repair supported
Resurrection of ASUS P526 is slightly complicated. JTAG pads are very small and sensitive thus extreme care must be taken when soldering wires to the board. Battery must be connected in order to establish JTAG connection.
Current resurrector re-flashes only the IPL area, and will not re-write MDOC XLOADER area (though write of this area is supported too).
Please note: DiskOnChip G4 memory has security features, due to which there is a risk of permanently blocking the access to the flash memory while re-flashing the XLOADER areas. Current resurrector will not touch the XLOADER zone, but it is possible you’re already holding such killed device in hands. If it is so you will see this error:
************************************************** **************
Detected a Not Initialized FLASH1 Chip ID: 0×0400/0xFBFF
ERROR: Selected FLASH Chip was not initialized by the DCC Loader
************************************************** **************
This can happen due to unknown protection keys used or due to permanently blocked MDOC chip. If latter is true we advise you to solder a new flash memory chip or throw this phone away to the trash bin.
To resurrect ASUS P526:
* Solder JTAG cable to ASUS P526 JTAG pads;
* Insert battery and connect USB cable to phone and PC;
* Make sure ASUS P526 is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
If phone not enters download mode after resurrection then it means XLOADER was damaged too but memory chip is still usable. In this case repeat resurrection using RAM Downloader Mode and when USB connection is established reflash the phone with official firmware.
To enter download mode:
* Disconnect PC cable;
* Insert battery;
* Move ‘Lock’ slider down, hold ‘OK’ key (on the left) and press ‘Power ON’ button. In few seconds you should see TriColor picture.
Additional info:
* Phone has DiskOnChip G4 memory type, which has security features. It has two password protected partitions (Password1 = 12345678, Password2 = 00000000);
* XLOADER re-flash is not performed in this resurrector on purpose. While re-flashing the XLOADER area there is a risk of permanently blocking the memory chip.
* Any write access (Erase or Write) on MDOC NAND memory range 0×00000000 to 0x0017FFFF is rejected by the DCC Loader
10.03.2011 CDMA ZTE F285 Repair supported
Resurrecting ZTE F285 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board. Resurrector re-flashes only firmware zone of the phone (0×000000 to 0x60FFFF).
To resurrect ZTE F285:
* Solder JTAG cable to ZTE F285 JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure ZTE F285 is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;
10.03.2011 RIFF JTAG Manager v1.27, RIFF Box Firmware v1.19
Whats new :
RIFF JTAG Manager v1.27
* Fixed access violation bug upon JTAG Manager startup if there is no RIFF Box detected and Cancel button is clicked.
* (SDK): more functions are now available (exported) for future Resurrector DLLs;
* Added flags for JTAG Manager to be able to retrieve memory chip size from the DCC Loader.
* Fixed initialization bug for NOR-related DCC Loadererss
* ScriptEngine: added options pocessing ‘/byte’, ‘/word’, ‘/long’ to data.save.binary instruction: thus it’s possible now to read memory through script using desired bus access width (8-,16-, or 32-bit widths). For example: “data.save.binary c:\myfile.bin 0×00..0x11FF /word” – will read 0×1200 bytes from memory into myfile.bin file starting from address 0×00 using 16-bit bus accesses.
Note: “Read Memory” button on the JTAG Read/Write page reads memory using 32-bit bus accesses only.
RIFF Box Firmware v1.19
* Added more H/W script (*.has) instructions;
* Added HTC security processing functions;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
-
11.03.2011 CDMA Huawei C5005 Unbrick – Repair supported
11.03.2011 CDMA Huawei C5005 Unbrick – Repair supported
Resurrecting Huawei C5005 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Resurrector re-flashes only firmware zone of the phone (0×000000 to 0xBFFFFF).
To resurrect Huawei C5005:
Solder JTAG cable to Huawei C5005 JTAG pads;
Insert USB Data cable into board and PC;
Make sure Huawei C5005 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
http://www.jtagbox.com/wp-content/up...1/03/c5005.jpg
-
RIFF JTAG - Samsung i607 Blackjack PDA, CDMA Huawei C5005, OMAP 1710 Support added
12.03.2011 Samsung SGH-i607 BlackJack PDA Unbrick, Dead Boot repair supported
Resurrecting Samsung i607 PDA part is easy. Phone requires battery presence in order to establish JTAG connection. If you additionally connect charger the phone will be auto powered on and there will be no need to press Power on key.
In case you experience connection problems, de-power phone completely, disconnect charger (if it was used), then insert battery, click Resurrection button in the JTAG Manger and immediately (within 0…1 seconds) press Power On key.
To unbrick Samsung i607 PDA part:
Solder JTAG cable to Samsung i607 PDA JTAG pads;
Make sure Samsung i607 PDA is selected in the list of models;
If only battery is connected – press Power On key shortly;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
11.03.2011 CDMA Huawei C5005 Unbrick – Repair supported
Resurrecting Huawei C5005 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Resurrector re-flashes only firmware zone of the phone (0×000000 to 0xBFFFFF).
To resurrect Huawei C5005:
Solder JTAG cable to Huawei C5005 JTAG pads;
Insert USB Data cable into board and PC;
Make sure Huawei C5005 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
De-solder JTAG wires;
OMAP 1710 Support added :
OMAP 1710 Specs,
OMAP 1710 based devices.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
-
RIFF JTAG - Toshiba Portege G900 Unbrick, Dead Boot repair supported
14.03.2011 Toshiba Portege G900 Unbrick, Dead Boot repair supported
Resurrection of Toshiba Portégé G900 PDA part is not hard. Battery is required for successful HALT operation. If USB Data Cable is connected phone is auto powered on when battery is inserted.
If during connect operation (“Establish communication with the phone…”) after 2-3 passes there is still no success (progress bar keeps running from 0 to 100% and so on) then remove battery and insert it again. If USB cable is not connected then press and hold Power On key.
Current resurrector re-flashes only the EBOOT and secondary EBOOT area, and will not re-write IPL area (though write of this area is supported too).
Please note: DiskOnChip G4 memory has security features, due to which there is a risk of permanently blocking the access to the flash memory while re-flashing the IPL areas. Current resurrector will not touch the IPL zone, but it is possible you’re already holding such killed device in hands. If it is so you will see this error:
************************************************** **************
Detected a Not Initialized FLASH1 Chip ID: 0×0400/0xFBFF
ERROR: Selected FLASH Chip was not initialized by the DCC Loader
************************************************** **************
This can happen due to unknown protection keys used or due to permanently blocked MDOC chip. If latter is true we advise you to solder a new flash memory chip or throw this phone away to the trash bin.
To resurrect Toshiba G900 PDA part:
* Solder JTAG wires to the Toshiba G900 PDA pads;
* Connect USB cable to phone and PC;
* Make sure Toshiba G900 PDA is selected in the list of models;
* Insert battery and click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter USB download mode:
* Disconnect PC cable;
* Insert battery;
* Hold ‘Left soft’ key (which is exactly above the Dial key) and press ‘Power ON’ button. In few seconds you should see red download screen.
To enter SD-card download mode:
* Disconnect PC cable;
* Insert battery;
* Hold ‘D’ key and press ‘Power ON’ button.
Additional info:
* Phone has DiskOnChip G4 memory type, which has security features. It has two password protected partitions (Password1 = 12345678, Password2 = 00000000);
* IPL re-flash is not performed in this resurrector on purpose. While re-flashing the IPL area there is a risk of permanently blocking the memory chip.
* Any write access (Erase or Write) on MDOC NAND memory range 0×00000000 to 0x0017FFFF is rejected by the DCC Loader. For full image writing convenience access to that range will not rise any error, data will just be ignored and reported as if it was written successfully, thus you still can write full image files using ‘Auto FullFlash Size’ checked.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
-
RIFF JTAG - Huawei E153U Broadband modem unbrick – dead boot repair supported
17.03.2011 Huawei E153U Broadband modem unbrick – dead boot repair supported
Resurrecting Huawei E153U is simple. Just make sure you solder all JTAG signals and insert modem into a USB port for it to get powered.
If modem is not detected by RIFFBOX JTAG, disconnect JTAG connector, re-insert modem into USB and then connect back the JTAG connector.
There are secured (QCSBL is signed) and non-secured (QCSBL is not signed) modem revisions exist. Resurrector will automatically detect board revision and will select proper data to be flashed.
No matter what h/w revision is you can select which partitions are to be flashed during resurrection process.
To resurrect Huawei E153U:
* Solder JTAG cable to Huawei E153U JTAG pads;
* Insert Huawei E153U modem into any USB port for power;
* Make sure Huawei E153U is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
RIFF BOX - ROVER PC EVO V7, MARVELL PXA3XX Generic NAND DCC Loader
21.03.2011 RoverPC EVO V7 Unbrick – Dead boot repair supported
RoverPC Evo V7 resurrection is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
To resurrect RoverPC Evo V7:
-Solder JTAG cable to RoverPC Evo V7 JTAG pads;
-Connect USB cable to phone and PC;
-Make sure RoverPC Evo V7 is selected in the list of models;
-Make sure a fixed TCK frequency is selected;
-Click Resurrect button;
-Wait till software signals a successful operation completion;
-Disconnect USB cable, de-solder JTAG wires;
-Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original firmware downloader software to restore it to the working state.
To enter download mode:
-Disconnect PC cable;
-Insert battery;
-Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On.
21.03.2011 MARVELL PXA3XX NAND Generic DLL Released
Resurrector PXA3XX contains only NAND DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager.
Embedded DCC Loader is designed to work inside of MCU's internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.
21.03.2011 - RIFF Box Firmware v1.21
Firmware 1.21
---------------------------
Added RX-polling feature (debugger-to-target) for PXA3XX DCC transfers.
RIFF BOX firmware is able now to wait (if resurrector DLL will request so) for PXA3XX target to be ready to accept
next packet over DCC: this feature slows down a little the JTAG-to-Target DCC
transfers but guaranties no packets loss for slow clocked targets;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
-
RIFF JTAG - Samsung GT-B7330 Omnia PRO Boot Repair Supported
22.03.2011 Samsung GT-B7330 Omnia PRO Boot Repair Supported
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“Samsung_B7330.dll” contains pinout, instructions and required repair files for Samsung GT-B7330 OmniaPRO Unbrick – Boot Repair.
-
RIFF BOX - ROVER PC EVO V7, MARVELL PXA3XX Generic NAND DCC Loader
21.03.2011 RoverPC EVO V7 Unbrick – Dead boot repair supported
RoverPC Evo V7 resurrection is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
To resurrect RoverPC Evo V7:
* Solder JTAG cable to RoverPC Evo V7 JTAG pads;
* Connect USB cable to phone and PC;
* Make sure RoverPC Evo V7 is selected in the list of models;
* Make sure a fixed TCK frequency is selected;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original firmware downloader software to restore it to the working state.
To enter download mode:
* Disconnect PC cable;
* Insert battery;
* Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On.
21.03.2011 MARVELL PXA3XX NAND Generic DLL Released
* Resurrector PXA3XX contains only NAND DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager.
Embedded DCC Loader is designed to work inside of MCU's internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.
21.03.2011 - RIFF Box Firmware v1.21
Firmware 1.21
---------------------------
* Added RX-polling feature (debugger-to-target) for PXA3XX DCC transfers.
RIFF BOX firmware is able now to wait (if resurrector DLL will request so) for PXA3XX target to be ready to accept
next packet over DCC: this feature slows down a little the JTAG-to-Target DCC
transfers but guaranties no packets loss for slow clocked targets;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
-
RIFF JTAG Updates - HTC Ozone/Chief, JTAG Manager v1.29 and more
31.03.2011 HTC Ozone XV6175 (HTC Chief) Unbrick, Boot Repair, Unlock, IMEI Repair, CID Update supported
Resurrecting HTC Chief is easy:
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.44.0000 SPL version.
Additionally, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘CEDA10000′.
As well, you can change CID – for this make sure ‘Repair Custom ID’ field is checked in the Resurrection Guide dialog.
To resurrect HTC Chief:
* Solder JTAG cable to HTC Chief JTAG pads;
* Make sure HTC Chief is selected in the list of models;
* Insert battery and connect USB Cable;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
31.03.2011 JTAG Manager v1.29, RIFF Box Firmware v1.21 released
JTAG Manager 1.29
—————————
* Fixed bug with plugins managing in case there is more than 1 plugin DLL available;
* Currently selected plugin is remembered now and will stay on next startups;
* Fixed Access Violation error during software startup in case there is none resurrector DLL present;
* Added Reset Method selection feature for more precise reset operation when Custom Target Settings is active;
* Updates manager & Updates tracking were completely reworked, and now are based not on the system time but on file’s hashing.
Thus since now on the JTAG Manager’s installation folder can be copied/moved/re-installed (whatever else) without need to re-download full set of files again.
* (SDK): more functions are now available (exported) for future Resurrector DLLs;
* Many cosmetic changes;
* FINALLY: “healed” the optimized DLL loading scheme:
User shall see: “Found and Initialized: XXX New and YYY Old External Repair Pack(s)” where XXX must be always non-zero only on first startup after there were new DLLs downloaded from the support.
On following JTAG Manager startups XXX shall be always equal to zero (!!!)
For example, after downloading 3 more new DLLs while there were 100 Resurrector DLLs already installed, after JTAG Manager restarts user shall see:
Found and Initialized: 3 New and 100 Old External Repair Pack(s)
on next and all following restarts user shall see:
Found and Initialized: 0 New and 103 Old External Repair Pack(s)
* Re-worked balloon hints system – Own (not windows’) balloons are shown, so no matter now what are the windows’ tray icon settings are.
* Added balloon hints for cases when target is not detected, error code 0×45, Device Id = 0x000000E1.
Don’t forget that balloons hints can be switched on or off from the DCC Read/Write page – click “Notifications…” and select”For Advanced Users” page to see settings
* - JTAG Manager now has new Icons http://www.jtagbox.com/wp-includes/i...icon_smile.gif
* - Improved JTAG Manager restarting during updating itself
Firmware 1.21
—————————
* Added RX-polling feature (debugger-to-target) for PXA3XX DCC transfers.
RIFF BOX firmware is able now to wait (if resurrector DLL will request so) for PXA3XX target to be ready to accept
next packet over DCC: this feature slows down a little the JTAG-to-Target DCC
transfers but guaranties no packets loss for slow clocked targets;
31.03.2011 RIFF Data Exchange Plugin 1.00 released
First release of the RIFF Data Exchange Plugin: please download it, and then select it on Usefull Plugins page in the JTAG Manager to read short description about the plugin’s abilities. In short it allows RIFF BOX users to share and use Full Image files in centralized manner without need to waste a lot of time for browsing countless forums.
Because of big sizes of Full Image files, we don’t host them, instead users share links to file sharing servers where the files are actually uploaded. (like megaupload.com, rapidshare.com and others) You can browse existent links for required image file or share your image file (by sharing a http link) to help other RIFF BOX users.
If you share image file please take attention to carefully fill file details so for other people this to be an easy task to search for required file (link)
If you used link to download file and found it good or bad or link to be broken – please Rate this link so other users see the usability of the link.
At the moment of first release of this plugin there are already few links shared so you’ll catch the idea fast.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
RIFF JTAG - CDMA Day ! QSC1100, Micromax C111, Huawei C2830 supported
06.04.2011 CDMA QUALCOMM QSC1100 Generic DLL released
Resurrector QSC1100 X14 contains only DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager.
Embedded DCC Loader is designed to work inside of MCU’s internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.
Initial H/W init sequence will setup MCU’s PLL with these parameters:
* Clock Multiplier = 0×14
Since few different versions of QSC1100 resurrector may exist (with different multiplier values) you may select the one which suits best to your device
06.04.2011 CDMA Micromax C111 Boot repair supported
Resurrecting Micromax C111 is simple. Board is auto powered on when battery is inserted and USB cable is connected.
There are 2 different hardware revisions of this phone – one is based on Qualcomm QSC1100 MCU and other – is Qualcomm QSC6010 MCU. Current resurrector shall be selected if you have QSC1100 revision.
Resurrector re-flashes only firmware zone of the phone (0×000000 to 0x6FFFFF).
To resurrect Micromax C111:
* Solder JTAG cable to Micromax C111 JTAG pads;
* Connect ignition cable for auto power on or use battery;
* Make sure Micromax C111 is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;
06.04.2011 CDMA Huawei C2830 Boot repair supported
Resurrecting Huawei C2830 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board. Since the JTAG test points are placed under keyboard sticker we recommend using USB data cable to supply power to the device.
Resurrector re-flashes only firmware zone of the phone (0×000000 to 0x5FFFFF).
Please note: if you do not have JIG (that is you solder wires instead) then black graphite covering has to be carefully scratched off in order to access copper surface of the pads.
To resurrect Huawei C2830:
* Solder JTAG cable to Huawei C2830 JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure Huawei C2830 is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
RIFF JTAG - CDMA Samsung B159, Samsung Galaxy Mini (S5570) Supported
06.04.2011 CDMA Samsung B159 Boot repair supported
Resurrecting Samsung B159 is simple. Board is auto powered on when battery is inserted and USB cable is connected.
Resurrector re-flashes only firmware zone of the phone (0×000000 to 0x57FFFF).
To resurrect Samsung B159:
* Solder JTAG cable to Samsung B159 JTAG pads;
* Connect ignition cable for auto power on or use battery;
* Make sure Samsung B159 is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
Special thanks goes to Mr Lalitg.
06.04.2011 Samsung Galaxy Mini (S5570) Unbrick – Boot repair supported
Samsung S5570 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.
To resurrect Samsung S5570 do this:
* Solder JTAG cable to Samsung S5570 JTAG pads;
* Insert battery and connect USB cable to phone and PC;
* Make sure Samsung S5570 is selected in the list of models;
* Click Resurrect button;
* Wait few seconds until software signals a successful operation completion;
* Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:
* Disconnect PC cable;
* Insert battery;
* Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On to enter Download Mode;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
RIFF JTAG - Samsung S7230E Wave 723 Unbrick – Boot Repair supported
08.04.2011 Samsung S7230E Wave 723 Unbrick – Boot Repair supported
Resurrecting Samsung S7230E is easy. To power the phone connect USB cable and insert battery. In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.
To resurrect Samsung S7230E:
* Solder JTAG cable to Samsung S7230E JTAG pads;
* Connect USB cable to phone and PC;
* Insert battery;
* Make sure Samsung S7230E is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state. We used MultiLoader 5.64 version.
To enter download mode:
* Disconnect PC cable;
* Insert battery;
* Hold both ‘Volume Down’ (on the left side of phone) and ‘Lock’ (right side bottom part) keys and press Power-On.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
RIFF JTAG - CDMA Motorola W150i (MSM6000) Repair supported
21.04.2011 CDMA Motorola W150i (MSM6000) Repair supported
Resurrecting Motorola W150i is simple. Phone is auto powered on with charger connected; battery presence is not required. Pin TMODE has to be connected to GND in order to enable JTAG connection.
Please note, MSM6000 draws power from JTAG pins, thus board can be detected via JTAG even without any power supplied. But for successful resurrection the power (battery or charger) is required. Thus when resurrection is complete don’t forget to disconnect phone from RIFF BOX to de-power it completely.
To resurrect Motorola W150i:
Solder JTAG cable to Motorola W150i JTAG pads;
Connect charger for auto power on or use battery;
Make sure Motorola W150i is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
RIFF JTAG - CDMA Haier C3010, LG LSP450T Repair supported
22.04.2011 CDMA Haier C3010, LG LSP450T Repair supported
Resurrecting Haier C3010 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chips with IDs 0x00EC/0x257E and 0x017E/0×2210. Proper data will be selected automatically depending on memory ID in your device.
To resurrect Haier C3010:
* Solder JTAG cable to Haier C3010 JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure Haier C3010 is selected in the list of models;
* Click Resurrect button;
* Choose which areas to flash;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;
Resurrecting LG LSP450T is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0×0020/0×8867
To resurrect LG LSP450T:
* Solder JTAG cable to LG LSP450T JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure LG LSP450T is selected in the list of models;
* Click Resurrect button;
* Choose which areas to flash;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
RIFF JTAG - More CDMA Today ! HTC Trophy Unlock, Unbrick and repair
-
RIFF JTAG - Samsung B2710 (Samsung Xcover 271) Unbrick / Repair supported
03.05.2011 Samsung B2710 (Samsung Xcover 271) Unbrick / Repair supported
Samsung B2710 resurrection is simple. Phone is auto powered on when USB Cable and battery are connected.
To resurrect Samsung B2710 do this:
* Solder JTAG cable to the Samsung B2710 JTAG pads;
* Connect USB cable to phone and PC;
* Make sure Samsung B2710 is selected in the list of models
* Click Resurrect button;
* Wait few seconds until software signals a successful operation completion;
* Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:
* Disconnect PC cable;
* Insert battery;
* Hold both ‘Volume Down’ and ’9′ keys and press Power-On. Screen lights up with Download mode message.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
RIFF JTAG - Samsung Nexus S, HTC Incredible C Unbrick/Boot repair supported
04.05.2011 HTC Droid Incredible ADR6300 (HTC Incredible C) Unbrick Dead Boot Repair supported
Resurrecting HTC Incredible C is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB3120000′.
To resurrect HTC Incredible C:
Solder JTAG cable to HTC Incredible C JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC Incredible C is selected in the list of models;
If you use battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume down’ key and press ‘Power ON’ button to enter HBoot menu;
Hold ‘Volume up’ key and press ‘Power ON’ button to enter Recovery mode;
04.05.2011 Samsung Nexus S (i9023) Unbrick Boot repair supported
Samsung I9023 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
Current resurrector has two different versions of primary boot loaders (PBL) embedded. This depends on hardware version of your phone which boot to use, thus in case of failure (cannot enter download mode after resurrection) of first loader try selecting another.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.
To resurrect Samsung I9023:
Solder JTAG cable to Samsung I9023 JTAG pads;
Connect microUSB cable to phone and PC;
Insert battery;
Make sure Samsung I9023 is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
RIFF JTAG - LG CU720 Shine Unbrick/Boot repair supported
07.05.2011 LG CU720 Shine Unbrick – Boot repair supported
Resurrecting LG CU720 is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
To resurrect LG CU720:
* Solder JTAG cable to LG CU720 JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure LG CU720 is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
RIFF JTAG - Samsung S5830, A867 Unbrick/Repair, Huawei Modem E5830 supported
12.05.2011 Samsung Galaxy Ace S5830 Unbrick – Boot repair supported
Samsung S5830 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.
To resurrect Samsung S5830 do this:
* Solder JTAG cable to Samsung S5830 JTAG pads;
* Insert battery and connect USB cable to phone and PC;
* Make sure Samsung S5830 is selected in the list of models;
* Click Resurrect button;
* Wait few seconds until software signals a successful operation completion;
* Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:
* Disconnect PC cable;
* Insert battery;
* Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On to enter Download Mode;
12.05.2011 Huawei E5830 Broadband modem Unbrick – Boot repair supported
Resurrecting Huawei E5830 is simple. Just make sure you solder all JTAG signals. Connection can be established with USB Cable connected, though in some rare cases battery presence may be required.
If modem is not detected by RIFFBOX JTAG, disconnect JTAG connector, re-insert modem into USB and then connect back the JTAG connector.
Please note, if only an USB cable is connected the device is detected by PC as unknown device. So, after resurrection in order to check if modem is alive make sure battery is connected.
To resurrect Huawei E5830:
* Solder JTAG cable to Huawei E5830 JTAG pads;
* Insert Huawei E5830 modem into any USB port for power;
* Make sure Huawei E5830 is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;
12.05.2011 Samsung Eternity A867 Unbrick - Boot repair supported
The Samsung A867 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
To resurrect Samsung A867:
* Solder JTAG cable to Samsung A867 JTAG pads;
* Connect USB cable;
* Make sure Samsung A867 is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
* Disconnect PC cable;
* Insert battery;
* Hold both ‘Volume Down’ and ‘Camera’ keys and press ‘Power ON’ button.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
RIFF JTAG - CDMA Huawei C5589, Dopod Magic A6188 ,Samsung Z630, Huawei E5832 added
13.05.2011 CDMA Huawei C5589 Unbrick – Boot repair supported
Resurrecting Huawei C5589 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x017E/0×2230
To resurrect Huawei C5589:
* Solder JTAG cable to Huawei C5589 JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure Huawei C5589 is selected in the list of models;
* Click Resurrect button;
* Choose which areas to flash;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;
Dopod Magic A6188 (HTC Sapp400) Unbrick, Unlock, IMEI and CID repair supported
The HTC Magic (SAPP400) is based on ESM7206A chipset. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.53.02000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘SAPP*****’. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.
To resurrect HTC Magic (SAPP400):
* Solder JTAG cable to HTC Magic (SAPP400) JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure HTC Magic (SAPP400) is selected in the list of models;
* If you use battery, press Power On key;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
* Disconnect PC cable;
* Insert battery;
* Hold ‘Back (←)’ key and press ‘Power ON’ button. In few seconds you should see download mode saying Fastboot USB.
13.05.2011 Samsung Z630 Unbrick – Boot repair supported
Resurrection of Samsung Z630 requires battery or external power supply. Most convenient way is to use additionally an USB cable: in this case power is auto powered on and there will be no need to hold power on key during connection startup.
Please note, phone will be detected even with only USB cable connected, but stable connection and stable data exchange will be achieved only when battery (or external power supply) is connected too.
To resurrect Samsung Z630:
* Solder JTAG cable to Samsung Z630 JTAG pads;
* Insert battery (or connect external power supply to the battery pads) and connect USB cable;
* Make sure Samsung Z630 is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
* Disconnect PC cable;
* Insert battery;
* Hold ’4′ key and press ‘Power ON’ button. In few seconds you should see light-blue screen.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
HTC_Mozart.dll & HTC_Trophy
HTC_Mozart.dll & HTC_Trophy
-------------------------------------
- Finally fixed an issure about ModelID. So ModelID is will now again be resurrected.
Those who have ModelID error just make resurrection again and all will be ok.
-
RIFF JTAG - More CDMA Models, new bug fix updates today
10.06.2011 More CDMA Models, new bug fix updates today
Whats new :
CDMA Models JTAG support :
- Huawei C2605
- Micromax MMX 250C
- ZTE WP829
- LG RD3640
Bug fix updates :
- Samsung S5830
- HTC Incredible C
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
RIFF JTAG – HTC Desire HD A9191 (HTC Ace) Unbrick, IMEI, CID, ModelID, Simlock repair
WHATS NEW!!!
- HTC Desire HD A9191 (HTC Ace) = Unbrick, IMEI, CID, ModelID, Simlock repair = WORLD FIRST ! ! !
RIFF JTAG - HTC Desire HD Discussion (Repair, Unlock, IMEI Repair)
Firmware 1.25
---------------------------
- added 5.0V USB Power On/Off controlling feature
- changed sequence for 32-bit write accesses for ARM11 core (MSM8xxx support)
JTAG Manager 1.33
---------------------------
- Improved connection policy:
Resurrection/DCC connection to device is implemented in such way that JTAG speed changes have 2 stages - booting stage and working stage.
Booting stage is the one from the connection start and until the DCC Loader upload is complete. Booting TCK/RTCK speed are setup
by JTAG Manager no matter what are the TCK settings by user (JTAG TCK Speed field in the JTAG Manager). Booting speed is hardcoded in the DLL.
After "booting" stage is complete, the "working" speed is set - the one which is selected by user in the JTAG TCK Speed field.
If Booting Speed in resurrector DLL is hardcoded as 'RTCK' the JTAG Manager would always use RTCK mode during booting stage.
Now policy is changed that is when user selects a fixed TCK frequency the JTAG Manager will automatically
change booting speed to the fixed TCK too.
- fixed bug: if "Use End Address" and "AutoFull Flash Size" were checked there was error setting valid length to read.
- for Advanced Users: advanced settings are now moved from the DCC Read/Write page ("Notifications...") into separate button on Box Service page (Advanced Settings button)
- added 5.0V USB Power On/Off controlling feature
For this go to Box Service page, click Advanced Settings: the Notifications dialog will be displayed,
go to "Advanced Settings" page and set desired mode for "Enable 5.0V output" checkbox.
When enabled, 5.0V power will be on after any "JTAG" operation executed and will remain "ON" until
box restart or until "Enable 5.0V output" checkbox is unchecked and any "JTAG" operation is executed.
- added optimization for flashing memory devices which are sector-based (like MDOC H3 or MMC/SD memory cards)
- if error code 0x3C (write-protect) is received no recover attempts are made.
RIFF Box – JTAG Revolution
-
RIFF JTAG - HTC Wildfire S A510E (HTC Marvel), 7 More CDMA models supported
07.07.2011 HTC Wildfire S A510E (HTC Marvel), More CDMA models supported.
Resurrecting HTC WildFireS is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.01.0002 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC4910000′. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.
To resurrect HTC WildFireS:
* Solder JTAG cable to HTC WildFireS JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure HTC WildFireS is selected in the list of models;
* If you use battery, press Power On key;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
* Disconnect PC cable;
* Insert battery;
* Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see usual android boot mode screen.
Following CDMA models are supported from today :
* Samsung B139 Repair/Unbrick, Read/Write NOR Flash
* Samsung B259 Repair/Unbrick, Read/Write NOR Flash
* Samsung B309 Repair/Unbrick, Read/Write NOR Flash
* Samsung B319 Repair/Unbrick, Read/Write NOR Flash
* Samsung B379 Repair/Unbrick, Read/Write NOR Flash
* Samsung B619 Repair/Unbrick, Read/Write NOR Flash
* Huawei C31 Repair, Read/Write NOR flash
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
RIFF JTAG - Samsung T749, Samsung E189 Unbrick - Boot repair supported
12.07.2011 Samsung T749, Samsung E189 Unbrick – Boot repair supported
The Samsung T749 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
To resurrect Samsung T749:
- Solder JTAG cable to Samsung T749 JTAG pads;
- Connect USB cable;
- Make sure Samsung T749 is selected in the list of models;
- Click Resurrect button;
- Wait till software signals a successful operation completion;
- Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
In case you cannot find firmware files use Global RIFF Link & Data Exchange plugin – at the moment of resurrector release there was shared full dump from alive Samsung T749 phone.
To enter download mode:
- Disconnect PC cable;
- Insert battery;
- Hold both ‘Volume Up’ and ‘Camera’ keys and press ‘Power ON’ button.
Resurrecting Samsung E189 is simple.
Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0×2256
To resurrect Samsung E189:
- Solder JTAG cable to Samsung E189 JTAG pads;
- Insert USB Data cable into board and PC;
- Make sure Samsung E189 is selected in the list of models;
- Click Resurrect button;
- Choose which areas to flash;
- Wait till software signals a successful operation completion;
- De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
Trích:
Được post bởi
HoangThong_hotrokythuat4
27.08.2010 – HTC Magic32 – SAPP300 – G2 unbrick/repair IMEI supported
Now resurrector accepts both Sapphire100 (0x301700E1) and Sapphire300 (0x201700E1) IDs
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“HTC_Magic32A.dll” contains pinout, repair instructions and required repair files for both “Sapphire100″ and “Sapphire300″ HTC Magic32A G2 phones.
http://www.jtagbox.com/wp-content/up...tc-magic-2.jpg
có hướng dẫn repair con này không anh?
-
RIFF JTAG - Latest Updates and News ! Here is short list of latest news :
RIFF JTAG – Qtek 9000 (HTC Universal) Unbrick – Boot repair supported « RIFF Box – JTAG Revolution
Other names for this device :
Bug fix updates :
Qualcomm Partition tool 1.04 :
- Added support for 4kb page code reading (Applies to HTC Models)
In case You want to read unlock code from dump with 4kb page, and You get "Simlock zone is not found" message, tick "Don't adjust HTC Partition for 4kb NAND pages" check box, and read partition again.
Beta testers required for Samsung Galaxy S II :
Samsung Galaxy S2 i9100 wanted for beta test ! ! !
Support for Exynos 4210 Samsung CPU is added, and will be released after tests.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
RIFF JTAG - Samsung GT-i8700 Omnia 7 , Samsung W299 Duos Unbrick - Boot repair suppor
29.07.2011 Samsung GT-i8700 Omnia 7 , Samsung W299 Duos Unbrick – Boot repair supported
Resurrecting Samsung I8700 is simple. Phone is auto powered on with USB Data Cable connected to the PC while battery is inside. In case you use the battery only please note you will have to press Power On key once.
To resurrect Samsung I8700:
Solder JTAG cable to Samsung I8700 JTAG pads;
Make sure Samsung I8700 is selected in the list of models;
Insert Battery into phone and connect USB cable (in case you not use USB cable, press once the Power ON key on the phone)
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Up’ and ‘Camera’ keys and press ‘Power ON’ button. In few seconds phone enters download mode.
Resurrecting Samsung W299 is simple. Phone is auto powered on with USB Data Cable connected to the PC while battery is inside. In case you use the battery only please note you will have to press Power On key once.
To resurrect Samsung W299:
Solder JTAG cable to Samsung W299 JTAG pads;
Make sure Samsung W299 is selected in the list of models;
Insert Battery into phone and connect USB cable (in case you not use USB cable, press once the Power ON key on the phone)
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
RIFF JTAG -Samsung Galaxy S II Unbrick Support and much more !
29.07.2011 New RIFF JTAG Updates :
- RIFF JTAG Manager v1.34
- RIFF Box firmware v1.26
- RIFF GDB Server v1.04
With new release we added support for new ARM core(s) - Cortex-A9 in single core and multicore configuration.
Project now supports Unicode, so there is Russian and Chinese language available !
JTAG Manager now supports 64bit addressing, thus allowing You to dump large memory chips (eMMC and iNAND) !
New resurrectors DLL-s
- Samsung Galaxy S II (Samsung i9100) Unbrick, Boot repair
- SonyEricsson x10 Unbrick, Boot repair
- Samsung CDMA B119
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
29.07.2011 Samsung I9100 Galaxy S II Unbrick – Boot repair supported, World First
Samsung I9100 is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core).
JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface. There is a big variety of versions of Galaxy II devices: GT-I9100, GT-I9100G, GT-I9100L, GT-I9100M, GT-I9100T, GT-I9101, GT-I9103, GT-I9108, GT-I9188, and maybe more. Some of them are based on different hardware platform – the OMAP4430 (Cortex-A9 Dual-Core). Thus make sure first which exact hardware version you have on hands.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
Phone has such booting sequence: ROM → FBL → IBL → PBL → SBL. Current resurrector will resurrect Partition Table (PIT) and SBL zones which are located in the iNAND (eMMC) memory. Write access to memory which contains FBL, IBL and PBL loaders is not supported currently, but in case your phone has these loaders damaged, you can choose “Initiate Download Mode” way of resurrection in order to directly put the phone into the Download Mode.
To resurrect Samsung I9100:
Solder JTAG cable to Samsung I9100 JTAG pads;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung I9100 is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
http://www.jtagbox.com/wp-content/up...alaxy-S-II.jpg
-
30.07.2011 New RIFF JTAG Updates :
- RIFF JTAG Manager v1.34
- RIFF Box firmware v1.26
- RIFF GDB Server v1.04
With new release we added support for new ARM core(s) - Cortex-A9 in single core and multicore configuration.
Project now supports Unicode, so there is Russian and Chinese language available !
JTAG Manager now supports 64bit addressing, thus allowing You to dump large memory chips (eMMC and iNAND) !
New resurrectors DLL-s
- Samsung Galaxy S II (Samsung i9100) Unbrick, Boot repair
- SonyEricsson x10 Unbrick, Boot repair
- Samsung CDMA B119
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
News RIFF JTAG – Sony Ericsson Xperia X8a (SE Shakira) Unbrick – Boot repair supported
News
RIFF JTAG – Sony Ericsson Xperia X8a (SE Shakira) Unbrick – Boot repair supported
by admin on Aug.02, 2011, under News
02.08.2011 Sony Ericsson Xperia X8a (SE Shakira) Unbrick – Boot repair supported
Resurrecting SE X8 is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted.
During resurrection, you can select which areas to be repaired. So you can choose only those areas which you know are damaged thus saving flashing time.
To resurrect SE X8:
Solder JTAG cable to SE X8 JTAG pads;
Insert USB Data cable into board and PC;
Make sure SE X8 is selected in the list of models;
If you use only battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
http://www.jtagbox.com/wp-content/up..._xperia_x8.jpg
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
-
03.08.2011 Samsung Galaxy Tab M180s Unbrick – Boot Repair supported
Samsung M180S is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in some cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.
To resurrect Samsung M180S:
Solder JTAG cable to Samsung M180S JTAG pads;
Connect USB cable to phone and PC;
Attach battery connector;
Make sure Samsung M180S is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.
Bug fix update :
Samsung S5830
Improved resurrection by adding few more zones to be reflashed.
Fixed issue with NAND chip not being detected (0xAAAA/0xAAAA ID)
CPU ID 0x303C10E1 added to allowed list
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
RIFF JTAG - JTAG Manager v1.35 released
04.08.2011 JTAG Manager v1.35 released
Whats new :
- Added an arbitrary feature “Settings by Code” to the DCC Read/Write page.
Main purpose is to improve support quality for users: via “Settings Code” string a supporter person sees all settings which were set by user on the DCC Read/Write page.
Though, end-user may benefit from this too: Use “Settings Code” string for JTAG Manager to automatically setup all DCC Read/Write settings
- Fixed data loss during read and save operations in case there is not enough disk space available to store required amount of data.
(for example reading full on DCC Read/Write page, or saving read full, etc).
Now available disk space checks are performed prior disk write operations.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
RIFF JTAG - JTAG Manager v1.35 released
04.08.2011 JTAG Manager v1.35 released
Whats new :
- Added an arbitrary feature “Settings by Code” to the DCC Read/Write page.
Main purpose is to improve support quality for users: via “Settings Code” string a supporter person sees all settings which were set by user on the DCC Read/Write page.
Though, end-user may benefit from this too: Use “Settings Code” string for JTAG Manager to automatically setup all DCC Read/Write settings
- Fixed data loss during read and save operations in case there is not enough disk space available to store required amount of data.
(for example reading full on DCC Read/Write page, or saving read full, etc).
Now available disk space checks are performed prior disk write operations.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
-
RIFF JTAG - Samsung Galaxy GIO (S5660) Unbrick - Boot repair supported
23.08.2011 Samsung Galaxy GIO (S5660) Unbrick – Boot repair supported
Samsung S5660 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.
To resurrect Samsung S5660 do this: Solder JTAG cable to Samsung S5660 JTAG pads;
Insert battery and connect USB cable to phone and PC;
Make sure Samsung S5660 is selected in the list of models;
Click Resurrect button;
Wait few seconds until software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode: Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘OK’ keys and press Power-On to enter Download Mode;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
