RIFF JTAG - 7 new models added - read inside !
30.08.2011 RIFF JTAG - 7 new models added !
Whats new :
- LG Models :
- Samsung :
- Sierra Wireless
- Pantech :
Please click "Check For Updates" button in order to download and apply new updates.
RIFF Box – JTAG Revolution
09.09.2011 HTC Desire S S510E (HTC Saga) – Unbrick, Unlock, CID, IMEI Update supported
Resurrecting HTC Desire S is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Desire S boards have JTAG interface disabled (that is enable MARM JTAG Fuse is ****n in the MSM8255 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL to0.98.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG8810000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE ****n then there is no way to resurrect your phone via JTAG interface.
To resurrect HTC Desire S:
Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
- Solder JTAG cable to HTC Desire S JTAG pads;
- Insert batter and connect USB Data cable;
- Make sure HTC Desire S is selected in the list of models;
- If you use only battery, press Power On key;
- Click Resurrect button;
- Wait till software signals a successful operation completion;
- Disconnect power supply, de-solder JTAG wires;
To enter download mode:
http://www.jtagbox.com/wp-content/up...-Desire-S1.jpg
- Disconnect PC cable;
- Insert battery;
- Hold ‘Volume Down’ key and press ‘Power ON’ button.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
03.10.2011 RIFF JTAG - Samsung and CDMA updates !
Whats new :
Added support for Samsung B209
Added support for Samsung S7330 Unbrick
Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.
RIFF Box – JTAG Revolution
RIFF JTAG – Samsung Focus (i917) Unbrick, Dead boot repair supported
by admin on Oct.04, 2011, under News
04.10.2011 Samsung Focus (i917) Unbrick, Dead boot repair supported
Resurrecting Samsung I917 is simple. Phone is auto powered on with USB Data Cable connected to the PC while battery is inside. In case you use the battery only please note you will have to press Power On key once.
To resurrect Samsung I917:
* Solder JTAG cable to Samsung I917 JTAG pads;
* Make sure Samsung I917 is selected in the list of models;
* Insert Battery into phone and connect USB cable (in case you not use USB cable, press once the Power ON key on the phone)
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
* Disconnect PC cable;
* Insert battery;
* Hold both ‘Volume Up’ and ‘Camera’ keys and press ‘Power ON’ button. In few seconds phone enters download mode.
http://www.jtagbox.com/wp-content/up...locked-380.jpg
JTAG Manager Version 1.36, RIFF Box Firmware v1.27 Released,Tegra 2 Support ! ! !
JTAG Manager Version 1.36, RIFF Box Firmware v1.27 Released,Tegra 2 Support ! ! !
- added fast presets for automatic selection of settings for most common operations on DCC Read/Write page
For this click Settings by Code button and select a desired preset from list and then click Apply Settings.
For example if user selects "Write Full Image into NAND memory" the valid settings on the DCC Read/Write page
for writting full images into devices with NAND memory will be automatically selected
- fixed serious bug which caused resurrector DLLs which do upload data into RAM to upload broken data
For example DLLs which start Downlad Mode directly use this feature.
- added feature to accept text name of memory chip from DCC Loader and display it (currently used to display eMMC memory product name)
- fixed bug for resumming interrupted DCC Read: ifvcurrently cached file size was greater than > 2GB
(that is if read was interrupted on point when there was already more than 2GB of data read) the new reading data was not appended to the readout file end, but instead the file was corrupted.
- fixed bug for saving big files (after reading on DCC Read/Write page): if size exceeded 0x7FFFFFFF bytes JTAG Manager show no free disk space error.
- added TEGRA2 chipset selection in the Target list
- fixed an issue with the resurrection progress bar: in some cases during resurrection operations the progress bar would always stay at 0%.
Firmware 1.27
---------------------------
- added TEGRA2 debugging support (dual-core Cortex-A9)
- added new breakpoint type: "address mismatch" which allows geniune single-stepping on Cortex-A8,A9 (CoreSight) targets
(thus GDB Server can now perform low-level single step commands)
07.10.2011 Samsung Galaxy II, OMAP4430 version supported (Samsung i9100G, Samsung i9108)
Added support for Samsung Galaxy II, OMAP4430 version supported
Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.
RIFF Box – JTAG Revolution
RIFF JTAG - HTC updates !
12.10.2011 HTC Desire Z (HTC Vision) Update
Whats new :
Added support for HTC Desire Z (HTC Vision)
Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.
RIFF Box – JTAG Revolution
RIFF JTAG - Samsung updates ! 19.10.2011 RIFF JTAG – Samsung Z500 supported !
Whats new :
Added support for: Samsung Z500
Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.
RIFF Box – JTAG Revolution
24.10.2011 HTC & Samsung updates !
Whats new :
Added support for: HTC Supersonic (EVO 4G)
Added support for: Samsung i520
Added support for: Samsung Corby II – S3850
Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.
RIFF Box – JTAG Revolution
RIFF JTAG - LG & HTC updates ! 24.10.2011 RIFF JTAG - LG & HTC updates !
Whats new :
Added support for: LG SH860
Added support for: HTC Desire CDMA
Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.
RIFF Box – JTAG Revolution
RIFF JTAG - Samsung updates !
26.10.2011 Samsung Galaxy S Plus (i9001) Unbrick, boot repair supported
Whats new : Samsung Galaxy S Plus (i9001)
Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.
RIFF Box – JTAG Revolution
RIFF JTAG - Samsung i9003, Samsung m820 supported 28.10.2011 - RIFF JTAG Updates
Whats new :
- Samsung i9003 (Samsung Galaxy SL) Unbrick, boot repair
- Samsung m820 (Samsung Galaxy Prevail) Unbrick, boot repair
- ZTE RD518 Boot repair
To download and install updates, please close all running applications and press "Check for Updates" button in RIFF JTAG Manager.
Carefully read resurrection manual for i9003 to avoid frustration ! http://forum.gsmhosting.com/ubb/smile.gif
RIFF Box – JTAG Revolution Galaxy RulerZZZZZZZ
11.11.2011 SonyEricsson Unlock/IMEI/TA Repair supported
Whats new :
With this release, we now support Unlock, IMEI repair and TA repair for listed SE models.
You can now totally rebuild software in these models, after replacing NAND chip for example. At the moment, we have following models released :
Remember that these models can have different names (e10, e15, u20 etc)
- x8
- x10
- x10 mini
- x10 mini pro
Please check up this link for more information :
RIFF JTAG – Unlock/IMEI/TA repair – SonyEricsson x8, x10, x10 Mini, x10 mini pro (e15, e10,u20 etc) « RIFF Box – JTAG Revolution
New JTAG Manager has been released too, together with new RIFF Box firmware. Please check this link for more :
RIFF JTAG – JTAG Manager v1.37, RIFF Box firmware v1.28 released « RIFF Box – JTAG Revolution
RIFF Box – JTAG Revolution - Galaxy RulerZZZZZZZZZZZZZZZZZ http://forum.gsmhosting.com/ubb/biggrin.gif
Hello
So, we need RIFF users with some free time and few SEMC phones.
- SE X2 Needed working phone ! ! !
- X8/E15 - not required anymore
- X10 - not required anymore
- X10 Mini/E10i - not required anymore
Thank You.
edit :
Now, after some models support is released, I'll try to explain what happens with SEMC QC based phones.
- SEMC boot is NEVER reflashed during update proces, hence phone can not have erased bootloader. This, however, can happen in unlocking process, hence we have added it as option.
- If Your phone has damaged TA (Trim Area or GDFS) then now is possible to repair it.
There are many phones which have some HW error, which results in not booting, not entering download mode or not reacting at all.
When You can repair Your phone ?
From many months of testing with Xperia x10i, we've found rather few situations when phone is actually fixed :
- Phone firmware update failed at AMSS area, and after this phone wont enter bootloader mode. To fix this problem, simply erase AMSS area, and this will allow phone to enter download mode.
- Phone boot is damaged by failed unlock
To fix this problem, simply tick "Repair BOOT" box and press "Resurrect"
- Phone has damaged TA (Trim Area) or wrong IMEI
To fix this problem, or repair IMEI, simply tick "Repair TA Zone" and enter correct IMEI number. Remember that IMEI change is illegal in some countries, and You're allowed only to REPAIR damaged IMEI !
http://www.jtagbox.com/downloads/man...EMC/Page00.bmp
If You wish to unlock Your phone for FREE, do this:
- Select "Unlock Your Phone" TAB
- Press "Unlock"
http://www.jtagbox.com/downloads/man...EMC/Page01.bmp
What settings are best for SEMC QC phones ?
- RTCK Sampling 8MHz
- External power + USB Cable
What to do in case that phone has no network ?
- Connect phone to RIFF Box
- Select model
- Click "Resurrection"
- Tick "Repair TA Zone"
- Enter valid IMEI
- Click "Resurrect"
Please understand :
- You CAN repair phones with erased or damaged TA (GDFS) area now.
- You CAN NOT repair phones with hardware problems.
I hope this is enough information for any possible situation, hence there is no need to ask same questions again and again.
19.11.2011 – QUALCOMM MDM6600 NAND Generic DLL released
Whats new:
QUALCOMM MDM6600 NAND DLL
Use this for phones which have MDM6600 in baseband – eg LG P999, iPhone 4s, and many other phones which use TEGRA2 AP CPU.
QUALCOMM MSM7227 OneNAND DLL (2kb page)
QUALCOMM MSM7227 OneNAND DLL (4kb page)
QUALCOMM QSC6xxx OneNAND DLL
All other QUALCOMM Generic DLL-s are now under same branch, so here is full revised list :
ESM7xxx L41 D04 NAND
MDM6600 NAND
MSM6xxx L06 D02 NAND
MSM7227 L41 D08 OneNAND
MSM7227 L41 D08 OneNAND 4k
MSM7xxx L41 D04 NAND
MSM7xxx L41 D08 NAND
QSC1100 x14 NOR
QSC60xx L18 D08 NOR
QSC6xx L20 D08 NOR
QSC60xx L24 D08 NOR
QSC6xxx L32 D08 NAND
QSC6xxx L36 D08 NAND
QSC6xxx L36 D08 OneNAND
QSD8xxx L41 D04 NAND
Press “Check for updates” button in order to download and install new files.
RIFF Box – JTAG Revolution
RIFF JTAG - CDMA updates !
- Added repair support for ZTE F280
- Added repair support for Micromax C100
- Added repair support for Intex In50
- Added repair support for Huawei ETS2225
- Added repair support for Huawei ETS 2222
- Added repair support for Huawei ETS2205
Please click “Check for Updates” button in Box Service TAB in order to download and install new files.
RIFF Box – JTAG Revolution
Samsung P1010 is based on the OMAP3630 (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.
Please note, in most cases you will be required to insert Samsung P1010 RIFF™ MagicCard into phone’s SD slot before starting resurrection. In case you don’t have such card yet, you can create it on the “Samsung P1010 RIFF™ MagicCard” page of the resurrector settings dialog.
This is IRAM version of the Samsung P1010 resurrector. We recommend you using it only in case you had problems connecting to phone with normal Samsung P1010 resurrector DLL.
To resurrect Samsung P1010:
* Solder JTAG cable to Samsung P1010 JTAG pads;Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
* Insert Samsung P1010 RIFF™ MagicCard into phone’s SD slot;
* Connect USB cable to phone and PC;
* Insert battery;
* Make sure Samsung P1010 is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect USB cable, de-solder JTAG wires;
To enter download mode:
* Disconnect PC cable;There are two DLL-s (Normal and iRAM version) – You can use iRam version in case normal one doesnt work properly. iRam version is much slower, but more robust.
* Insert battery;
* Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.
http://www.jtagbox.com/wp-content/up...ab-verizon.jpg
CDMA Models added today :
* ZTE AC2766Please click “Check for Updates” button in order to download and install new updates.
* ZTE AC2746
* AnyData ADU555C
RIFF JTAG – Samsung Star Duos (C6712) Unbrick – Boot repair supported
29.11.2011 Samsung Star Duos (C6712) Unbrick – Boot repair supported
Samsung C6712 resurrection is simple. Battery is not required. To power the board it’s most convenient to use an USB Data Cable.
In order to contact to JTAG pads you may need to carefully scratch off paint covering (mask layer) above them. Sometimes there is reset problem with these phones, thus you may need to disconnect and then connect USB cable again.
To resurrect Samsung C6712 do this:
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
- Solder JTAG cable to Samsung C6712 JTAG pads;
- Insert battery and connect USB cable to phone and PC;
- Make sure Samsung C6712 is selected in the list of models
- Click Resurrect button;
- Wait few seconds until software signals a successful operation completion;
- Disconnect USB cable, de-solder JTAG wires;
To enter download mode:
__
- Disconnect PC cable;
- Insert battery;
- Hold both ‘Volume Down’ and ‘SIM Swap’ keys and press Power-On.
http://www.jtagbox.com/wp-content/up...os-black-1.jpg
RIFF JTAG - Samsung updates !
29.11.2011 Samsung Star Duos (C6712) Unbrick – Boot repair supported
Whats new :
Added support for: Samsung Star Duos (C6712) Unbrick
Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.
RIFF Box – JTAG Revolution
22.11.2011 CDMA Huawei C2856 Supported
Added support for : Huawei C2856
Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.
RIFF Box – JTAG Revolution
RIFF JTAG - Direct JTAG Access to Flash Memory Plugin
16.12.2011 Direct JTAG Access to Flash Memory Plugin v1.00
Details Here:- Memory Plugin v1.00
Bug Fix updates :-
ZTE_AC2746.dll
-------------------------------------
- ID 0x100F80E1 is addedd to allowed list
Samsung_S239.dll
-------------------------------------
- ID 0x100FA0E1 is addedd to allowed list
ZTE_MF180S.dll
-------------------------------------
- ID 0x401200E1 is addedd to allowed list
Samsung_B379.dll
-------------------------------------
- ID 0x220B30E1 is addedd to allowed list
Samsung_M820.dll
-------------------------------------
- ID 0x503E00E1 is addedd to allowed list
Samsung_S5570.dll
-------------------------------------
- ID 0x503C10E1 is addedd to allowed list
JTAG Manager 1.38
---------------------------
Added feature to disable Target ID check during resurrection
If current ID is not supported by a DLL, user can switch off ID check and still be able to try resurrection.
Though, we don't recommend it. Do it only if you are sure what you're doing and if you're sure that device
with unmatched target ID is still exactly the same model as stated in DLL.
Please note, upon JTAG Manager exe startup this option is automatically switched off.
To disable Target ID do the following:
-> Box Service -> Advanced Settings -> Tick "Ignore TARGET IDCODE . . ."
http://www.jtagbox.com/downloads/man...es/ID_Code.jpg
Added preset "Erase Full NAND/NOR Memory" (for this use Settings by Code button)
DCC operations presets will ensure proper use of DCC TAB features. To select DCC Operation preset, do the following:
-> DCC Read/Write TAB -> Settings By Code -> Select desired preset
http://www.jtagbox.com/downloads/man...des/preset.jpg
Firmware 1.29
---------------------------
MPCore targets handling is improved.
Fixed bug in the ARM7 handling routines: h/w breakpoints were disabled each time any halt operation was performed
Added auxiliary instruction which improves GDB Server functionality.
29.12.2011 Samsung Galaxy Note (GT-i9220) Unbrick – Boot Repair Supported
Samsung I9220 AP (PDA Part) is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
To resurrect Samsung I9220 AP:
Solder JTAG cable to Samsung I9220 AP JTAG pads;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung I9220 AP is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.
http://www.jtagbox.com/wp-content/up...220-galaxy.jpg
10.01.2012 Samsung SGH-T759 Exhibit 4G Unbrick – Boot Repair supported
Added support for Samsung SGH-T759 Exhibit 4G
Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.
RIFF Box – JTAG Revolution
10.01.2012 Samsung GT-i8150 Galaxy W (Samsung Ancora) Unbrick – Boot repair supported
Resurrecting Samsung I8150 is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Please note, MSM8255T is dual core chipset – it has ARM11 and Qualcomm Scorpion cores. During power on sequence only ARM11 core is visible on the JTAG chain. If boots are not completely damaged and it comes up to initializing of the Scorpion core then Scorpion core appears on the JTAG chain too. This will shift ARM11 from TAP0 into TAP1 position on the chain, while current resurrector has the ARM11 core hardcoded at TAP0 position. Thus make sure to establish JTAG connection in the time range while Scorpion core is not visible yet.
To resurrect Samsung I8150:
Solder JTAG cable to Samsung I8150 JTAG pads;
Make sure Samsung I8150 is selected in the list of models;
Insert battery and connect USB Data cable;
If you use only battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button.
http://www.jtagbox.com/wp-content/up...0_galaxy_w.jpg
HTC Inspire 4G A9192 (HTC Stallion) Unbrick, Boot, IMEI, CID, ModelID, Unlock supported
Resurrecting HTC Inspire is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Inspire boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 0.85.0024. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD9812000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.
To resurrect HTC Inspire:
* Solder JTAG cable to HTC Inspire JTAG pads;Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
* Insert batter and connect USB Data cable;
* Make sure HTC Inspire is selected in the list of models;
* If you use only battery, press Power On key;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;
To enter download mode:
* Disconnect PC cable;http://www.jtagbox.com/wp-content/up...inspire_4g.jpg
* Insert battery;
* Hold ‘Volume Down’ key and press ‘Power ON’ button.
HTC Panache/Glacier/My Touch 4G Unbrick, IMEI, CID, ModelID, Unlock supported
Resurrecting HTC Glacier is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Glacier boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM7230 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write SPL version 0.86.0000. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD1510000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.
To resurrect HTC Glacier:
* Solder JTAG cable to HTC Glacier JTAG pads;Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
* Insert batter and connect USB Data cable;
* Make sure HTC Glacier is selected in the list of models;
* If you use only battery, press Power On key;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;
To enter download mode:
* Disconnect PC cable;_
* Insert battery;
* Hold ‘Volume Down’ key and press ‘Power ON’ button.
http://www.jtagbox.com/wp-content/up...tc_panache.jpg
09.02.2012 Samsung Galaxy Precedent SCH-M828 Unbrick supported
Samsung M828 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.
To resurrect Samsung M828 do this:
Solder JTAG cable to Samsung M828 JTAG pads;Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
Insert battery and connect USB cable to phone and PC;
Make sure Samsung M828 is selected in the list of models;
Click Resurrect button;
Wait few seconds until software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
To enter download mode:
Disconnect PC cable;http://www.jtagbox.com/wp-content/up...nt-M828C-c.jpg
Insert battery;
Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On to enter Download Mode;
14.02.2012 HTC ThunderBolt 4G ADR6400 (HTC Mecha) Unbrick – Boot repair supported
14.02.2012 HTC ThunderBolt 4G ADR6400 (HTC Mecha) Unbrick – Boot repair supported
14.02.2012 HTC ThunderBolt 4G ADR6400 (HTC Mecha) Unbrick – Boot repair supported
Resurrecting HTC Thunderbolt CP (Modem Part) part is easy.
Phone is auto powered on with USB Data Cable connected to the PC while battery is inside; sometimes during connection pressing Power On key may be required.
Please note, CP Part’s power is controlled by the AP Part, thus you may experience constant connection loses after definite ammounts of time (1-2-5-x seconds). If this keeps interferring the resurrection process, solder additionall JTAG interface cable to the AP pads, select AP resurrector DLL, go to the JTAG Read/Write page and halt AP core, then switch back to the CP JTAG interface.
To resurrect HTC Thunderbolt CP (Modem Part) Part:
Solder JTAG cable to HTC Thunderbolt CP JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC Thunderbolt CP is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
Resurrecting HTC Thunderbolt AP (PDA Part) is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.04.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG0510000’.
There is option to reflash BOOT and RECOVERY zones.
_
Bug Fix
HTC_DesireS.dll
-------------------------------------
- ID 0x27B360E1 is added to allowed list
HTC_Supersonic.dll
-------------------------------------
- added resurrection data for 4Kb NAND chips, so now DLL has data for both 4KB and 2KB versions.
Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.
RIFF Box – JTAG Revolution
RIFF JTAG - Samsung P6200, Huawei IDEOS S7, ZTE V9, Orange Boston, and more Some important news for today :
New updates:
Bug fixes:
- Samsung GT-P6200 Galaxy Tab 7.0 Plus Unbrick/Boot repair
- ZTE Light Tab (ZTE V9) Unbrick/Boot repair
- Huawei Ideos S7 Unbrick/Boot repair
- Orange Boston (Commtiva Z71) Unbrick/Boot repair
- Samsung Galaxy TAB (P1000N) Unbrick/Boot repair
- CDMA Samsung F219 Unbrick/Boot repair
Have a nice weekend ! http://forum.gsmhosting.com/ubb/biggrin.gif
- QSC1100_X14_NOR,
- QSC60XX_L18_D08_NOR,
- QSC60XX_L20_D08_NOR,
- QSC60XX_L24_D08_NOR
RIFF Box – JTAG Revolution
RIFF JTAG - RIFF JTAG Manager v1.39 Released !25.02.2012 JTAG Manager 1.39 released
Whats new:PLEASE NOTE!!! New resurrectors data base format is used in 1.39 version, thus
- Fixed bug which caused poping-up of ‘Out of Free Disk space’ window error while real error was just a failed HASH.
- eMMC chip size is now represented not only in bytes but additionally, for visual convenience, in Mega/Giga bytes
- Addres/Length fields on DCC Read/Write and JTAG Read/Write pages are changed into custom GUI representation: now 12(or 8)-digit hex values are shown in more human ‘readable’ way.
- For more convenient work with the DCC Read/Write page features there was added standard lengths list, so user can set ‘human readable’ length value instead of manual typing of correct hexadecimal length value. For this just click combo box near Data Length field and select a desired length.
Example:
.
http://www.jtagbox.com/wp-content/up.../DCC_size2.jpg
Now its possible to select any value from 1MB to 16GB, plus, in case of writing file, You can simply use “File Size” to automatically read opened file size and use it’s length.- Added balloon hints to suggest what to do in case user has ‘DLL was not Accepted’ issue.
- Selected resurrector DLL version is shown in logging windows now along with Model name, for example:
“Selected Resurrector: [NoName x1234 V1.00]“- Added “Search for DLL” button on the Resurrection page:
As RIFFBOX grows up on number of supported devices, searching visually through the big lists of supported models for a definite device name became a tiresome procedure.
Now user can search for required model simply typing part of model name in the search dialog (for this select “Search for DLL for this Model Name” and type some part of device name you’re looking for)
Example:
.
http://www.jtagbox.com/wp-content/up...12/02/name.jpg
.
Besides this, there is feature to search for resurrectors compatible with specific IDCODE. For example, if you have a not supported device in hands with ID = 0xXXXXXXXX, you can search for DLLs which work with such ID and try to connect your device using one of such ‘compatible’ DLLs. (for this select “Search for DLL with same IDCODE” and type IDCODE you’re looking for)
Example:
.
http://www.jtagbox.com/wp-content/up.../02/IDCODE.jpg
upon first start the JTAG MANGER WILL RESTART 1-5 TIMES in order to re-load and re-fresh all existing resurrector DLLs.
www.riffbox.org
Hello,
First, this is MAINLY for users with slow or bad internet connection. We have prepared torrent tracker and seed box, so hopefully users who experience problems with regular update download, can benefit from this.
Requirements :
- RIFF Box tracker account
- Torrent client
- Some free time to waste
Once You register and activate Your account, You can log in and browse torrents. At the moment, there is single torrent file, containing all current resurrectors DLL-s released by now.
Now, install uTorrent client (if You already don't have one) and do some settings first :
- Location of downloaded files : "C:\Program Files\RIFF Box JTAG Manager" (Or any other folder from where You run JTAG Manager exe)
- Open downloaded Torrent file and confirm download location
- Select files which You want to download
Keep in mind :
- JTAG Manager should be closed while You download files with torrent client
- Torrent client should be closed while You work with JTAG Manager
Since this is JUST test, things may not work well, so please report ANY kind of errors You may encounter.
If You need help or if You have any question/requests, please post here:
RIFF JTAG - Torrent Tracker public discussion
PLEASE dont ask stupid questions, because I will make ugly jokes if You do so.
28.02.2012 RIFF JTAG Updates:
Whats new:
* RIFF JTAG – Samsung SGH-i777 Galaxy S II Unbrick – Boot Repair supported, World First ! ! !Come to the dark side, we'll rule the Galaxy !
* RIFF JTAG – Samsung GT-S7500 Galaxy Ace Plus Unbrick – Boot Repair supported, World First ! ! !
RIFF Box – JTAG Revolution
06.03.2012 RIFF JTAG – Samsung SGH-T499 Dart (Samsung Tass) Unbrick – Boot Repair supported
Repairing bricked Samsung T499 is easy with RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is inside. In case you use the battery only please note you will have to press Power On key once.
To resurrect Samsung T499:
Solder JTAG cable to Samsung T499 JTAG pads;Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
Make sure Samsung T499 is selected in the list of models;
Insert Battery into phone and connect USB cable (in case you not use USB cable, press once the Power ON key on the phone)
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
To enter download mode:
Disconnect PC cable;http://www.jtagbox.com/wp-content/up...-t499_dart.jpg
Insert battery;
Hold both ‘Volume Up’ and ‘Home’ keys and press ‘Power ON’ button. In few seconds phone enters download mode.
New update JTAG-Pro Tool Aka GPGJTAG V1.23
http://www.gsmsaigon.vn/images/statusicon/wol_error.gifThis image has been resized. Click this bar to view the full image. The original image is sized 900x4564.http://www.gpgdragonsupport.com/ftpp...gpgjtag123.jpg
http://www.gsmsaigon.vn/images/statu...ser_online.gif http://www.gsmsaigon.vn/images/buttons/quote.gif
Resurrecting LG P350 is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
To resurrect LG P350:
Solder JTAG cable to LG P350 JTAG pads;Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods. We used KDZ_FW_UPD update software (with settings Type = 3GQCP, PhoneMode = EMERGENCY) to flash the *.KDZ firmware into phone.
Insert USB Data cable into board and PC;
Make sure LG P350 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
To enter emergency mode:
Disconnect PC cable;http://www.jtagbox.com/wp-content/up...optimus_me.jpg
Insert battery;
Hold ‘Volume down’ key and press ‘Power ON’ button. In few seconds you should see emergency mode screen saying “DOWNLOAD MODE”.
13.03.2012 RIFF JTAG - SonyEricsson new BOOTROM support and more !
Whats new:
Unlock/Repair TA is now supported for new BOOTROM version in following models:
E15a (SE_E15a.dll),HTC Neon Unbrick – Boot Repair, IMEI and CID update supported.
E15i (SE_X8.dll),
U20a (SE_U20a.dll),
U20i (SE_U20i.dll),
E10i (SE_X10_Mini.dll)
www.jtagbox.com
vậy admin cho em hỏi ? em có riff box nhưng ko bít nó để làm gì ? nge anh em nói là để repain điện thoại chạy hệ điều hành anroi có đúng ko ạ! và cho em hỏi thêm về cách repain bằng riff làm ra sao? và thực hiện như thế nào? cách sử dụng riffbox như thế nào? khi riff box đi kèm chỉ có 4 phụ kiện ? và những phụ kiện này để làm ji? nếu được thì admin có thể post 1 bài viết hướng dẫn chi tiếc về cách sử dụng riff box được ko ạ! để anh em chua biết sử dụng riff hiểu thêm và thao tác an toàn hơn! xin cảm ơn admin>....
em là người mới mong anh em giúp đỡ ! thắc mắc của em nói riêng và của anh em trong ngề sở hữu riff box nói chung. thì cũng có mấy ai biết sử dụng riff box ! ý kiến của em cũng như bao anh em khác! vì em ko bít lập topic nên mới mạn phép vào đây đăng bài và hỏi mong admin và anh em thông cảm! xin chân thành cảm ơn! rất mong anh em đã sử dụng riff chỉ giáo và chia sẻ. thank!
RIFF JTAG – HTC Sensation (HTC Pyramid) Unbrick, Unlock, ModelID, CID, IMEI repair Supported
by admin on Mar.14, 2012, under News
14.03.2012 RIFF JTAG – HTC Sensation 4G (HTC Pyramid) Unbrick, Unlock, ModelID, CID, IMEI repair Supported
Repairing bricked HTC Sensation is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 1.18.0000. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG5813000’.
There is option to reflash BOOT and RECOVERY zones.
To resurrect HTC Sensation:
Solder JTAG cable to HTC Sensation JTAG pads;Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
Insert batter and connect USB Data cable;
Make sure HTC Sensation is selected in the list of models;
If you use only battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
To enter download mode:
Disconnect PC cable;http://www.jtagbox.com/wp-content/up..._Sensation.jpg
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button.