C2-03 hay khởi động lại xin giúp đỡ.

[nguyenlaluong]

tình hình là em nhân một em C2-03 bật nguồn lên dùng một lúc lại khởi động lại , em chạy phần mềm, tháo thẻ nhớ ra , cả sim nhưng vẫn not ok anh em ai gặp bệnh này rồi xin chỉ em cái.

[KHA_MOBILE67]

anh bạn có thể nói rõ tí không vậy...anh lấy mx box chạy xem sau nhé anh..rồi tính tiếp nhé anh

[TÚ CÒI]

post cái log lên anh zai

[nguyenlaluong]

MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 3], SN: C08598C8
Connection status: UHCI:HUB::USB 1.10 (Full-speed)
Driver: nmwcdnsuc, ver: 7.1.32.70
Module ver: 1.0.0.19228(10-11-2011), Library ver: 1.0.0.13150(10-11-2011)
Make sure USB cable, Battery and charger are removed from device.
Insert USB cable, Battery back to device(make sure to have fully charged battery).
Insert Charger or Press phone's power button(if flashing doesnt start automatically)
Waiting for USB device ...
Device connected: nmwcdnsuc\Nokia USB Flashing Generic, PORT_ID: EAC265
Device synchronized.
CPU: XGOLD 213
Using embedded SBL from MCU.
Sending EBL Loader...OK
Sending EBL ...OK
Getting EBL Version ...
Boot mode: 0xCC
EBL version major/minor: 10.46
EBL version : Quantum_Bootloader_10.46_M1S1
Protocol version suggested by phone: 3
Set baud rate to: 6.50 Mbps
Flash ID: 0089 8982 [Intel NU48F512,512 Mbits]
Processing file: rm702__06.51.mcusw
Downloading item CODE:rm702__06.51.mcusw_ebl_psi.fls, num block: 4, size: 28 MB
Erasing area 0x40000000-0x4001FFFE ...OK
Programming completed in 0.422 s
Erasing area 0x40040000-0x4005FFFE ...OK
Programming completed in 0.406 s
Erasing area 0x40060000-0x4015FFFE ...OK
Programming completed in 1.562 s
Erasing area 0x40280000-0x41D3FFFE ...OK
Programming completed in 35.079 s
Checksum verified (0x2541)
Processing file: rm702__06.51.ppm_v
Downloading item CUSTackage_v.ppm_ebl_psi.fls, num block: 1, size: 5.26 MB
Erasing area 0x41DC0000-0x42300876 ...OK
Programming completed in 6.672 s
Checksum verified (0x7850)
Processing file: rm702__06.51.image_v_059D3X0
Downloading item CUSTackage_v_059D3X0.image.fls, num block: 1, size: 10.13 MB
Erasing area 0x424C0000-0x43E1FFFE ...OK
Programming completed in 13.515 s
Checksum verified (0xBDB9)
Total time for flashing process(boot+erase+write) was 7 min 13.078 s
Waiting for device boot up ...
Device connected: nmwcdnsuc\Nokia USB Flashing Generic, PORT_ID: EAC265
Verifying communication to device...
ERROR: Could not verify communication !

Phone type: RM-702 (C2-03)
SW version: V 06.51 15-07-11 RM-702 (c) Nokia
Imei plain: 35864004362428-8
Product code: 059D3X0
Battery voltage: 3759 mV, current: 98 mA
Language Pack:
- not available.

Imei net: 35864004362428
Version: SIMLOCK SERVER
Provider: GSM Test Operator
Counter: 0/3, 0/10

CONFIG_DATA: 0010100000000000
PROFILE_BITS: 800000000003000B

BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
FULL FACTORY... OK
Completed in 0.532 s
FULL FACTORY... OK
USER DATA... OK
LEAVE FACTORY... OK
SERVICE CENTER... OK
SOFTWARE UPGRADE... OK
PRODUCTION TUNING... OK
Reset User Code (to default:12345) ... OK
Completed in 1.328 s
FULL FACTORY... OK
USER DATA... OK
LEAVE FACTORY... OK
SERVICE CENTER... OK
SOFTWARE UPGRADE... OK
PRODUCTION TUNING... OK
Reset User Code (to default:12345) ... OK
Completed in 0.703 s

[toilatoi142001]

ERROR: Could not verify communication !

còn báo lỗi nè bạn ơi

[song_van_xo_bo]

viết pm cho em nó cái rồi tính tiếp

[HQDuan_GSM]

bạn cho nó cái ver đụng nóc đi, nếu vẫn not ok thì cho e nguồn cắn tí thuốc lắc xem thế nào. good luck




Lưu ý:Không Spam bài cũ .Close topic