ace xin xem dùm em log 2630

[ĐƠ_NGUYỄN]

2630 xài bình thường chỉ bị vào camera thì bị xanh màng hình, check thì ok, nhưng flash thì bị lổi thế này. bây giờ máy mất nguồn luôn. nhờ mấy pro giúp đỡ, thanks

[ĐƠ_NGUYỄN]

đây là log của em nó




MXKEY Serial: [MxKey Team HTI Flasher Interface (WinUSB) 5] - C0855D93
Using device: HTI BOX, FW ver: 00.24
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.0.0
Module ver: 1.0.0.18624(06-08-2011), Library ver: 1.0.0.12274(06-08-2011)
ASIC ID: 0x3162 [UPP_8M ver: 6.2]
SecondaryBoot: u3_2nd.fia [DCT4] version: 4.76.0 revision: 0.7 size: 0x9A8
Supported Ids: 3040, 2292, 2293, 3162, 3166, 3168
FlashID0: 0020 881C [ST M58LR256JU,256 Mbits] page size: 128 K type: NOR area: 01000000-02FFFFFF
FlashID1: 0000 0001 [unused/removed]
ExtBUSC: AD7E B61B 00FF 1040 0000 0000 0000 0000
Algorithm: u3_intel.fia [DCT4 ALGORITHM] version: 4.76.0 revision: 0.7 size: 0x56A0
Supported Ids: 3040, 2292, 2293, 3162, 3166, 3168
Performing Flash Authentication ...ASIC type: 11
UEM Imei: Empty
Flash Imei: 35865801267484
RPL saved to "C:\mobileEx\3.5\data\backup\RPL\_BACK.rpl"
Processing MCU file: rm298__05.62.mcusw
[DCT4,DCT4 ALGORITHM] size: 10.67 MB
Supported Ids: 3160, 3161, 3162, 3164, 3166
ASIC ID: 0x3162 [UPP_8M ver: 6.2]
SecondaryBoot: u3_2nd.fia [DCT4] version: 4.76.0 revision: 0.7 size: 0x9A8
Supported Ids: 3040, 2292, 2293, 3162, 3166, 3168
FlashID0: 0020 881C [ST M58LR256JU,256 Mbits] page size: 128 K type: NOR area: 01000000-02FFFFFF - COMBO FLASH
ExtBUSC: AD7E B61B 00FF 1040 0000 0000 0000 0000
Algorithm: u3_intel.fia [DCT4 ALGORITHM] version: 4.76.0 revision: 0.7 size: 0x56A0
Supported Ids: 3040, 2292, 2293, 3162, 3166, 3168
Performing Flash Authentication ...Area [01000000-0101FFFF] erased in 0.531 s
Area [01020000-01C3FFFF] erased in 50.641 s
Flash programming ...
Programming completed in 6 min 29.656 s
File Processed in 7 min 32.078 s
Processing CNT file: rm298__05.62.image_v
[DCT4,DCT4 ALGORITHM] page size: 128 K size: 4.63 MB
Supported Ids: 3160, 3161, 3162, 3164, 3166
ASIC ID: 0x3162 [UPP_8M ver: 6.2]
SecondaryBoot: u3_2nd.fia [DCT4] version: 4.76.0 revision: 0.7 size: 0x9A8
Supported Ids: 3040, 2292, 2293, 3162, 3166, 3168
FlashID0: 0020 881C [ST M58LR256JU,256 Mbits] page size: 128 K type: NOR area: 01000000-02FFFFFF - COMBO FLASH
ExtBUSC: AD7E B61A 1BBE 0BE2 7D58 6BE4 DBEE 6514
Algorithm: u3_intel.fia [DCT4 ALGORITHM] version: 4.76.0 revision: 0.7 size: 0x56A0
Supported Ids: 3040, 2292, 2293, 3162, 3166, 3168
Performing Flash Authentication ...Area [02000000-02DBFFFF] erased in 56.766 s
Area [02DC0000-02F9FFFF] erased in 7.828 s
Converting UCP blocks to 128 K.
Flash programming ...
Programming completed in 2 min 33.610 s
Extract fail, service not ready?
Content extract fail, continue anyway ...
File Processed in 5 min 7.813 s
Processing PPM file: rm298__05.62.ppm_v
[DCT4,DCT4 ALGORITHM] size: 3.19 MB
Supported Ids: 3160, 3161, 3162, 3164, 3166
Boot error: CC CC CC 00
- Repeat the procedure. Sometimes it is a matter of temporary communication problem or similar.
- Check that all used cable are solid without any visible damage and have good contact. If possible, try with other cables.
- On rare occasions phone might be damaged or dead. So, if possible, try with another phone.
flashing terminated !
Task failed at (0800002A)!!!
Last RX buffer: 02 00

[viethuy_mobi]

lấy box kahcs flash lại đi bạn . chứ mx flash chán lắm

[mjnhtuan123]

ban kiểm tra lại cáp.piuot

[TÚ CÒI]

Extract fail, service not ready?
Content extract fail, continue anyway ...
lỗi đoạn này nè
kiếm sợi cáp khác,box khác flat xem sao

[tienbaodhhh]

bạn đánh sạch chỗ tiếp xúc, flash lại là ok ngay thôi

[ĐƠ_NGUYỄN]

em đem qua mxkey , jaf điều không nhận cáp, flash thì bị lổi nhưng check lại thì thế này


MXKEY Serial: [MxKey Team HTI Flasher Interface (WinUSB) 5] - C0855D93
Using device: HTI BOX, FW ver: 00.24
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.0.0
Module ver: 1.0.0.18624(06-08-2011), Library ver: 1.0.0.12274(06-08-2011)
ASIC ID: 0x3162 [UPP_8M ver: 6.2]
SecondaryBoot: u3_2nd.fia [DCT4] version: 4.76.0 revision: 0.7 size: 0x9A8
Supported Ids: 3040, 2292, 2293, 3162, 3166, 3168
FlashID0: 0020 881C [ST M58LR256JU,256 Mbits] page size: 128 K type: NOR area: 01000000-02FFFFFF
FlashID1: 0000 0001 [unused/removed]
ExtBUSC: AD7E B61A 1BBE 0BE2 7D58 6BE4 DBEE 6514
Algorithm: u3_intel.fia [DCT4 ALGORITHM] version: 4.76.0 revision: 0.7 size: 0x56A0
Supported Ids: 3040, 2292, 2293, 3162, 3166, 3168
Performing Flash Authentication ...ASIC type: 11
UEM Imei: Empty
Flash Imei: 35865801267484
MasterCode: 5042007177
RPL saved to "C:\mobileEx\3.5\data\backup\_BACK.rpl"

Phone type: RM-298 (Nokia 2630)
SW version: V 05.62 02-07-08 RM-298 (c) Nokia
Imei plain: 35865801267484-5
Imei OTP: 35865801267484
Product code: 0549387
Cellular system: GSM
ASIC ID: 0x3162, type: 11
Ppm Id: V
Language Pack:
- not available.

Imei net: 35865801267484
Version: SIMLOCK SERVER
Provider: GSM Test Operator
Counter: 0/3, 0/10

CONFIG_DATA: 0010100000000000
PROFILE_BITS: 800000000001000B

BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN