[Xin giúp] xem giúp log 1280

[99999]

máy rớt nước , đã vệ sinh kỷ , bắm phím nguốn kim nhít nhẹ , đã flash lại nhưng not ok , nhờ ae giúp

đây là log của em nó

MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 3], SN: C0855D93
Using device: HTI, FW ver: 00.50, SN: 0000B3E9
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0
Module ver: 1.0.0.21151(13-07-2012), Library ver: 1.0.0.14214(25-10-2012)
Device synchronized.
CPU: XGOLD 110
Using embedded SBL from MCU.
Sending EBL Loader ...OK
Sending EBL ...OK
Getting EBL Version ...
Boot mode: 0xCC
EBL version major/minor: 10.19
EBL version: Default_RAM_Bootloader
Set baud rate to: 921.60 Kbit/s
Flash ID: 0020 88C0 - 23280003 [ST M58MWR064FU,64 Mbits]
CFI information:
Flash settings: 0/1, size: 0x00800000
2 Block regions:
127 x 0x00010000 = 0x007F0000
8 x 0x00002000 = 0x00010000
EBL ready !
Processing file: rm647_006.200
Downloading item CODE:hw_b2_rm647_r06.200.fls, num block: 3, size: 3.99 MB
Erasing area 0x00800000-0x00A0FFFE ...OK
Programming completed in 50.187 s
Erasing area 0x00C60000-0x00E4D5BE ...OK
Programming completed in 46.734 s
Erasing area 0x00FFC000-0x00FFC03E ...OK
Programming completed in 0.188 s
Error reading checksum!
Processing file: rm647_006.20mr
Downloading item CUST:hw_b2_rm647_006.20mr.fls, num block: 1, size: 1.10 MB
Erasing area 0x00210000-0x003288BE ...OK
Programming completed in 24.578 s
Checksum mismatch: Phone calculated 0x0033, software calculated 0xB874
Processing file: rm6470_nai06.20mr
Downloading item CUST:hw_b2_rm6470_nai06.20mr.fls, num block: 1, size: 305.83 KB
Erasing area 0x00EB0000-0x00EFBA3E ...OK
Programming completed in 6.453 s
Checksum mismatch: Phone calculated 0x00F0, software calculated 0xD819
Total time for flashing process(boot+erase+write) was 3 min 25.562 s

[BMmobile]

khò ép nhẹ con Xgold xem sao nhé bạn

[A & T Mobile]

cho cái log check lên nhìn cho dễ.
rớt nước thì vệ sinh sạch sẽ.not ok gỡ con tích hợp ra làm lại chân
ko dk thì thay mới chứ rớt nước ít khi do pm lắm

[99999]

còn đây là log check
MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 3], SN: C0855D93
Using device: HTI, FW ver: 00.50, SN: 0000B3E9
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0
Module ver: 1.0.0.21151(13-07-2012), Library ver: 1.0.0.14214(25-10-2012)
Device synchronized.
CPU: XGOLD 110
Using embedded SBL from MCU.
Sending EBL Loader ...OK
Sending EBL ...OK
Getting EBL Version ...
Boot mode: 0xCC
EBL version major/minor: 10.19
EBL version: Default_RAM_Bootloader
Set baud rate to: 921.60 Kbit/s
Flash ID: 0020 88C0 - 23280003 [ST M58MWR064FU,64 Mbits]
CFI information:
Flash settings: 0/1, size: 0x00800000
2 Block regions:
127 x 0x00010000 = 0x007F0000
8 x 0x00002000 = 0x00010000
EBL ready !

[A & T Mobile]

làm con tích hợp đi thớt ơi

[mobingoc]

lắc con tích hợp cpu đi bạn

[duykhanh_gsm]

gỡ upp làm chân lun đi , dòng này upp có vĩ làm chân rồi sợ chi

[Trường_Mobile]

đo lại đường màn hình,đường bsi tù up ra,thay thử các tụ gần chân pin không được thì mới đung tới upp

[99999]

đã 0k do đức mạch màng hình , thanks all