[Xin giúp] cần giúp restore rpl và file pm cho n200 bằng mxbox

[thichphamobi]

như tiêu đề mình vừa thay cặp cho con n200 read rpl và file pm đầy đủ nhưng tài mình chưa làm bao giờ nên không biết cách nên không biết bắt đầu từ đâu nhờ ae ai rảnh team giúp mình để học hỏi với nếu đc thì buzz yahoo hsinhmobile_hg@yahoo.com mình nha!

[tuanthanh99hp1]

đã thay cặp n200 máy khác vào thì mở nguồn ok luôn sao phải viết gì nữa bạn .viết rpl vào mà không backup tiếp thì thay cặp nữa đấy

[phithanhmobile]

thay cặp là lên thôi chứ rpl gì đâu phải backup thay 1 con ,mà dòng này thay thi thay 1 cặp

[thichphamobi]

giúp em với em thay nguyên cặp sang mà sao nó lại không lên đc luôn MXKEY [MxKey Team HTI PLUS Flasher Interface 1], SN: C08747FC
Using device: USB ROM and HTI, FW ver: 00.50, SN: 0100C15D
Connection status: UHCI:HUB::USB 1.10 (Full-speed)
Driver: NMWCD, ver: 7.1.32.75
Module ver: 1.0.0.21151(13-07-2012), Library ver: 1.0.0.14195(13-07-2012)
Make sure USB cable, Battery and charger are removed from device.
Insert USB cable, Battery back to device(make sure to have fully charged battery).
Insert Charger or Press phone's power button(if flashing doesnt start automatically)
Waiting for USB ROM device ...
Device synchronized.
CPU: XGOLD 213
Using embedded SBL from MCU.
Sending EBL Loader...OK
Sending EBL ...OK
Getting EBL Version ...
Boot mode: 0xCC
EBL version major/minor: 10.46
EBL version: Quantum_Bootloader_10.46_M1S1
Protocol version suggested by phone: 3
Set baud rate to: 6.50 Mbit/s
Flash ID: 0089 8982 - 23280001 [Intel NU48F512,512 Mbits]
CFI information:
Flash settings: 0/1024, size: 0x04000000
1 Block regions:
512 x 0x00020000 = 0x04000000
EBL ready !
Waiting for USB device removal ...OK
Waiting for USB device arrival ...OK
Waiting for device boot up ...
Device connected: nmwcdc\Nokia USB Phonet, PORT_ID: 26FA6D6
Verifying communication to device OK.


Phone type: RM-761 (Nokia 200)
SW version: V 11.64 07-06-12 RM-761 (c) Nokia
Imei plain: 12345610654321-?
Product code: 059K957
Battery voltage: 3760 mV, current: 45 mA
Cellular system: GSM
ASIC ID: 0x0000, type: 11
Ppm Id: V
Language Pack:
- not available.

Camera config: 06150103XXXXXX, ver:

Imei plain is invalid !!!
SIMLOCK_DATA corrupted!

[KIÊN NGUYỄN MOBILE]

cặp này cũng đia rồi chủ thớt ơi Imei quá đẹp

[hà_vũng tàu]

giúp em với em thay nguyên cặp sang mà sao nó lại không lên đc luôn MXKEY [MxKey Team HTI PLUS Flasher Interface 1], SN: C08747FC
Using device: USB ROM and HTI, FW ver: 00.50, SN: 0100C15D
Connection status: UHCI:HUB::USB 1.10 (Full-speed)
Driver: NMWCD, ver: 7.1.32.75
Module ver: 1.0.0.21151(13-07-2012), Library ver: 1.0.0.14195(13-07-2012)
Make sure USB cable, Battery and charger are removed from device.
Insert USB cable, Battery back to device(make sure to have fully charged battery).
Insert Charger or Press phone's power button(if flashing doesnt start automatically)
Waiting for USB ROM device ...
Device synchronized.
CPU: XGOLD 213
Using embedded SBL from MCU.
Sending EBL Loader...OK
Sending EBL ...OK
Getting EBL Version ...
Boot mode: 0xCC
EBL version major/minor: 10.46
EBL version: Quantum_Bootloader_10.46_M1S1
Protocol version suggested by phone: 3
Set baud rate to: 6.50 Mbit/s
Flash ID: 0089 8982 - 23280001 [Intel NU48F512,512 Mbits]
CFI information:
Flash settings: 0/1024, size: 0x04000000
1 Block regions:
512 x 0x00020000 = 0x04000000
EBL ready !
Waiting for USB device removal ...OK
Waiting for USB device arrival ...OK
Waiting for device boot up ...
Device connected: nmwcdc\Nokia USB Phonet, PORT_ID: 26FA6D6
Verifying communication to device OK.


Phone type: RM-761 (Nokia 200)
SW version: V 11.64 07-06-12 RM-761 (c) Nokia
Imei plain: 12345610654321-?
Product code: 059K957
Battery voltage: 3760 mV, current: 45 mA
Cellular system: GSM
ASIC ID: 0x0000, type: 11
Ppm Id: V
Language Pack:
- not available.

Camera config: 06150103XXXXXX, ver:

Imei plain is invalid !!!
SIMLOCK_DATA corrupted!

imei 12345..... đẹp thế còn chờ gì nữa mà k thay tiếp cặp khác ?