RIFF BOX JTAG New Update AE Post ở đây

[TuấnPhát_GSM]

22.03.2011 Samsung GT-B7330 Omnia PRO Boot Repair Supported

Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“Samsung_B7330.dll” contains pinout, instructions and required repair files for Samsung GT-B7330 OmniaPRO Unbrick – Boot Repair.

[TuấnPhát_GSM]

21.03.2011 RoverPC EVO V7 Unbrick – Dead boot repair supported


RoverPC Evo V7 resurrection is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.


To resurrect RoverPC Evo V7:

* Solder JTAG cable to RoverPC Evo V7 JTAG pads;
* Connect USB cable to phone and PC;
* Make sure RoverPC Evo V7 is selected in the list of models;
* Make sure a fixed TCK frequency is selected;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original firmware downloader software to restore it to the working state.


To enter download mode:

* Disconnect PC cable;
* Insert battery;
* Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On.


21.03.2011 MARVELL PXA3XX NAND Generic DLL Released

* Resurrector PXA3XX contains only NAND DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager.

Embedded DCC Loader is designed to work inside of MCU's internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.

21.03.2011 - RIFF Box Firmware v1.21

Firmware 1.21
---------------------------

* Added RX-polling feature (debugger-to-target) for PXA3XX DCC transfers.

RIFF BOX firmware is able now to wait (if resurrector DLL will request so) for PXA3XX target to be ready to accept
next packet over DCC: this feature slows down a little the JTAG-to-Target DCC
transfers but guaranties no packets loss for slow clocked targets;


Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

[TuấnPhát_GSM]

31.03.2011 HTC Ozone XV6175 (HTC Chief) Unbrick, Boot Repair, Unlock, IMEI Repair, CID Update supported

Resurrecting HTC Chief is easy:
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.44.0000 SPL version.
Additionally, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘CEDA10000′.
As well, you can change CID – for this make sure ‘Repair Custom ID’ field is checked in the Resurrection Guide dialog.


To resurrect HTC Chief:

* Solder JTAG cable to HTC Chief JTAG pads;
* Make sure HTC Chief is selected in the list of models;
* Insert battery and connect USB Cable;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


31.03.2011 JTAG Manager v1.29, RIFF Box Firmware v1.21 released

JTAG Manager 1.29
—————————

* Fixed bug with plugins managing in case there is more than 1 plugin DLL available;
* Currently selected plugin is remembered now and will stay on next startups;
* Fixed Access Violation error during software startup in case there is none resurrector DLL present;
* Added Reset Method selection feature for more precise reset operation when Custom Target Settings is active;
* Updates manager & Updates tracking were completely reworked, and now are based not on the system time but on file’s hashing.
Thus since now on the JTAG Manager’s installation folder can be copied/moved/re-installed (whatever else) without need to re-download full set of files again.
* (SDK): more functions are now available (exported) for future Resurrector DLLs;
* Many cosmetic changes;
* FINALLY: “healed” the optimized DLL loading scheme:
User shall see: “Found and Initialized: XXX New and YYY Old External Repair Pack(s)” where XXX must be always non-zero only on first startup after there were new DLLs downloaded from the support.
On following JTAG Manager startups XXX shall be always equal to zero (!!!)
For example, after downloading 3 more new DLLs while there were 100 Resurrector DLLs already installed, after JTAG Manager restarts user shall see:
Found and Initialized: 3 New and 100 Old External Repair Pack(s)
on next and all following restarts user shall see:
Found and Initialized: 0 New and 103 Old External Repair Pack(s)
* Re-worked balloon hints system – Own (not windows’) balloons are shown, so no matter now what are the windows’ tray icon settings are.
* Added balloon hints for cases when target is not detected, error code 0×45, Device Id = 0x000000E1.
Don’t forget that balloons hints can be switched on or off from the DCC Read/Write page – click “Notifications…” and select”For Advanced Users” page to see settings
* - JTAG Manager now has new Icons http://www.jtagbox.com/wp-includes/i...icon_smile.gif
* - Improved JTAG Manager restarting during updating itself

Firmware 1.21
—————————

* Added RX-polling feature (debugger-to-target) for PXA3XX DCC transfers.

RIFF BOX firmware is able now to wait (if resurrector DLL will request so) for PXA3XX target to be ready to accept
next packet over DCC: this feature slows down a little the JTAG-to-Target DCC
transfers but guaranties no packets loss for slow clocked targets;

31.03.2011 RIFF Data Exchange Plugin 1.00 released


First release of the RIFF Data Exchange Plugin: please download it, and then select it on Usefull Plugins page in the JTAG Manager to read short description about the plugin’s abilities. In short it allows RIFF BOX users to share and use Full Image files in centralized manner without need to waste a lot of time for browsing countless forums.


Because of big sizes of Full Image files, we don’t host them, instead users share links to file sharing servers where the files are actually uploaded. (like megaupload.com, rapidshare.com and others) You can browse existent links for required image file or share your image file (by sharing a http link) to help other RIFF BOX users.


If you share image file please take attention to carefully fill file details so for other people this to be an easy task to search for required file (link)
If you used link to download file and found it good or bad or link to be broken – please Rate this link so other users see the usability of the link.
At the moment of first release of this plugin there are already few links shared so you’ll catch the idea fast.


Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


RIFF Box – JTAG Revolution

[TuấnPhát_GSM]

06.04.2011 CDMA QUALCOMM QSC1100 Generic DLL released


Resurrector QSC1100 X14 contains only DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager.
Embedded DCC Loader is designed to work inside of MCU’s internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.


Initial H/W init sequence will setup MCU’s PLL with these parameters:

* Clock Multiplier = 0×14

Since few different versions of QSC1100 resurrector may exist (with different multiplier values) you may select the one which suits best to your device

06.04.2011 CDMA Micromax C111 Boot repair supported


Resurrecting Micromax C111 is simple. Board is auto powered on when battery is inserted and USB cable is connected.
There are 2 different hardware revisions of this phone – one is based on Qualcomm QSC1100 MCU and other – is Qualcomm QSC6010 MCU. Current resurrector shall be selected if you have QSC1100 revision.
Resurrector re-flashes only firmware zone of the phone (0×000000 to 0x6FFFFF).
To resurrect Micromax C111:

* Solder JTAG cable to Micromax C111 JTAG pads;
* Connect ignition cable for auto power on or use battery;
* Make sure Micromax C111 is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;


06.04.2011 CDMA Huawei C2830 Boot repair supported


Resurrecting Huawei C2830 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board. Since the JTAG test points are placed under keyboard sticker we recommend using USB data cable to supply power to the device.
Resurrector re-flashes only firmware zone of the phone (0×000000 to 0x5FFFFF).
Please note: if you do not have JIG (that is you solder wires instead) then black graphite covering has to be carefully scratched off in order to access copper surface of the pads.


To resurrect Huawei C2830:

* Solder JTAG cable to Huawei C2830 JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure Huawei C2830 is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


RIFF Box – JTAG Revolution

[TuấnPhát_GSM]

06.04.2011 CDMA Samsung B159 Boot repair supported



Resurrecting Samsung B159 is simple. Board is auto powered on when battery is inserted and USB cable is connected.
Resurrector re-flashes only firmware zone of the phone (0×000000 to 0x57FFFF).



To resurrect Samsung B159:

* Solder JTAG cable to Samsung B159 JTAG pads;
* Connect ignition cable for auto power on or use battery;
* Make sure Samsung B159 is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
Special thanks goes to Mr Lalitg.

06.04.2011 Samsung Galaxy Mini (S5570) Unbrick – Boot repair supported


Samsung S5570 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.


To resurrect Samsung S5570 do this:

* Solder JTAG cable to Samsung S5570 JTAG pads;
* Insert battery and connect USB cable to phone and PC;
* Make sure Samsung S5570 is selected in the list of models;
* Click Resurrect button;
* Wait few seconds until software signals a successful operation completion;
* Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:

* Disconnect PC cable;
* Insert battery;
* Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On to enter Download Mode;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

[TuấnPhát_GSM]

08.04.2011 Samsung S7230E Wave 723 Unbrick – Boot Repair supported

Resurrecting Samsung S7230E is easy. To power the phone connect USB cable and insert battery. In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.


To resurrect Samsung S7230E:

* Solder JTAG cable to Samsung S7230E JTAG pads;
* Connect USB cable to phone and PC;
* Insert battery;
* Make sure Samsung S7230E is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state. We used MultiLoader 5.64 version.


To enter download mode:

* Disconnect PC cable;
* Insert battery;
* Hold both ‘Volume Down’ (on the left side of phone) and ‘Lock’ (right side bottom part) keys and press Power-On.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

[TuấnPhát_GSM]

21.04.2011 CDMA Motorola W150i (MSM6000) Repair supported


Resurrecting Motorola W150i is simple. Phone is auto powered on with charger connected; battery presence is not required. Pin TMODE has to be connected to GND in order to enable JTAG connection.
Please note, MSM6000 draws power from JTAG pins, thus board can be detected via JTAG even without any power supplied. But for successful resurrection the power (battery or charger) is required. Thus when resurrection is complete don’t forget to disconnect phone from RIFF BOX to de-power it completely.


To resurrect Motorola W150i:

Solder JTAG cable to Motorola W150i JTAG pads;
Connect charger for auto power on or use battery;
Make sure Motorola W150i is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


RIFF Box – JTAG Revolution

[TuấnPhát_GSM]

22.04.2011 CDMA Haier C3010, LG LSP450T Repair supported


Resurrecting Haier C3010 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chips with IDs 0x00EC/0x257E and 0x017E/0×2210. Proper data will be selected automatically depending on memory ID in your device.


To resurrect Haier C3010:

* Solder JTAG cable to Haier C3010 JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure Haier C3010 is selected in the list of models;
* Click Resurrect button;
* Choose which areas to flash;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;

Resurrecting LG LSP450T is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0×0020/0×8867


To resurrect LG LSP450T:

* Solder JTAG cable to LG LSP450T JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure LG LSP450T is selected in the list of models;
* Click Resurrect button;
* Choose which areas to flash;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

[TuấnPhát_GSM]

So, its resurrection times

Updates for today :

* RIFF JTAG – HTC 7 Trophy T8686 (HTC Spark) Unbrick, Unlock, IMEI Repair, CID Update, ModelID Repair supported « RIFF Box – JTAG Revolution
* RIFF JTAG – CDMA ZTE C370 Repair supported « RIFF Box – JTAG Revolution
* RIFF JTAG – CDMA Haier C6000 Repair supported « RIFF Box – JTAG Revolution
* RIFF JTAG – CDMA Haier C5100 Repair supported « RIFF Box – JTAG Revolution
* RIFF JTAG – CDMA Haier C2040 Repair supported « RIFF Box – JTAG Revolution

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

[TuấnPhát_GSM]

03.05.2011 Samsung B2710 (Samsung Xcover 271) Unbrick / Repair supported


Samsung B2710 resurrection is simple. Phone is auto powered on when USB Cable and battery are connected.
To resurrect Samsung B2710 do this:

* Solder JTAG cable to the Samsung B2710 JTAG pads;
* Connect USB cable to phone and PC;
* Make sure Samsung B2710 is selected in the list of models
* Click Resurrect button;
* Wait few seconds until software signals a successful operation completion;
* Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:

* Disconnect PC cable;
* Insert battery;
* Hold both ‘Volume Down’ and ’9′ keys and press Power-On. Screen lights up with Download mode message.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


RIFF Box – JTAG Revolution