RIFF BOX JTAG New Update AE Post ở đây

RIFF JTAG - Latest Updates and News ! Here is short list of latest news :

RIFF JTAG – Qtek 9000 (HTC Universal) Unbrick – Boot repair supported « RIFF Box – JTAG Revolution

Other names for this device :

• I-Mate JASJAR (HTC Universal)
  
  
• Dopod 900 (HTC Universal)
  
  
• O2 XDA Exec (HTC Universal)
  
  
• T-Mobile MDA Pro (HTC Universal)
  
  
• Orange SPV M5000 (HTC Universal)
  
  
• Qtek 9000 (HTC Universal)
  
  
• Grundig GR980 (HTC Universal)
  
  
• Vodafone VPA IV / v1640 (HTC Universal)
  
  

Bug fix updates :

• HTC_Wildfire.dll
  
  - Added feature to flash RECOVERY and BOOT zones during resurrection.
  - Added code reading option
• HTC_WildfireS.dll
  - By mistake was released DLL for usual HTC Wildfire model. Now is ok. http://forum.gsmhosting.com/ubb/biggrin.gif
  
  Thanks to Tatek and Basar for help. Free beers for both http://forum.gsmhosting.com/ubb/smile.gif

Qualcomm Partition tool 1.04 :

• Added support for 4kb page code reading (Applies to HTC Models)

In case You want to read unlock code from dump with 4kb page, and You get "Simlock zone is not found" message, tick "Don't adjust HTC Partition for 4kb NAND pages" check box, and read partition again.

Beta testers required for Samsung Galaxy S II :

Samsung Galaxy S2 i9100 wanted for beta test ! ! !

Support for Exynos 4210 Samsung CPU is added, and will be released after tests.


Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


RIFF Box – JTAG Revolution

29.07.2011 Samsung GT-i8700 Omnia 7 , Samsung W299 Duos Unbrick – Boot repair supported


Resurrecting Samsung I8700 is simple. Phone is auto powered on with USB Data Cable connected to the PC while battery is inside. In case you use the battery only please note you will have to press Power On key once.

To resurrect Samsung I8700:

Solder JTAG cable to Samsung I8700 JTAG pads;
Make sure Samsung I8700 is selected in the list of models;
Insert Battery into phone and connect USB cable (in case you not use USB cable, press once the Power ON key on the phone)
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Up’ and ‘Camera’ keys and press ‘Power ON’ button. In few seconds phone enters download mode.

Resurrecting Samsung W299 is simple. Phone is auto powered on with USB Data Cable connected to the PC while battery is inside. In case you use the battery only please note you will have to press Power On key once.


To resurrect Samsung W299:

Solder JTAG cable to Samsung W299 JTAG pads;
Make sure Samsung W299 is selected in the list of models;
Insert Battery into phone and connect USB cable (in case you not use USB cable, press once the Power ON key on the phone)
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

29.07.2011 New RIFF JTAG Updates :

- RIFF JTAG Manager v1.34
- RIFF Box firmware v1.26
- RIFF GDB Server v1.04

With new release we added support for new ARM core(s) - Cortex-A9 in single core and multicore configuration.

Project now supports Unicode, so there is Russian and Chinese language available !

JTAG Manager now supports 64bit addressing, thus allowing You to dump large memory chips (eMMC and iNAND) !

New resurrectors DLL-s


- Samsung Galaxy S II (Samsung i9100) Unbrick, Boot repair
- SonyEricsson x10 Unbrick, Boot repair
- Samsung CDMA B119

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

29.07.2011 Samsung I9100 Galaxy S II Unbrick – Boot repair supported, World First

Samsung I9100 is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core).

JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface. There is a big variety of versions of Galaxy II devices: GT-I9100, GT-I9100G, GT-I9100L, GT-I9100M, GT-I9100T, GT-I9101, GT-I9103, GT-I9108, GT-I9188, and maybe more. Some of them are based on different hardware platform – the OMAP4430 (Cortex-A9 Dual-Core). Thus make sure first which exact hardware version you have on hands.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
Phone has such booting sequence: ROM → FBL → IBL → PBL → SBL. Current resurrector will resurrect Partition Table (PIT) and SBL zones which are located in the iNAND (eMMC) memory. Write access to memory which contains FBL, IBL and PBL loaders is not supported currently, but in case your phone has these loaders damaged, you can choose “Initiate Download Mode” way of resurrection in order to directly put the phone into the Download Mode.

To resurrect Samsung I9100:

Solder JTAG cable to Samsung I9100 JTAG pads;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung I9100 is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
http://www.jtagbox.com/wp-content/up...alaxy-S-II.jpg

30.07.2011 New RIFF JTAG Updates :

- RIFF JTAG Manager v1.34
- RIFF Box firmware v1.26
- RIFF GDB Server v1.04

With new release we added support for new ARM core(s) - Cortex-A9 in single core and multicore configuration.

Project now supports Unicode, so there is Russian and Chinese language available !

JTAG Manager now supports 64bit addressing, thus allowing You to dump large memory chips (eMMC and iNAND) !

New resurrectors DLL-s


- Samsung Galaxy S II (Samsung i9100) Unbrick, Boot repair
- SonyEricsson x10 Unbrick, Boot repair
- Samsung CDMA B119

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

News
RIFF JTAG – Sony Ericsson Xperia X8a (SE Shakira) Unbrick – Boot repair supported

by admin on Aug.02, 2011, under News

02.08.2011 Sony Ericsson Xperia X8a (SE Shakira) Unbrick – Boot repair supported

Resurrecting SE X8 is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted.
During resurrection, you can select which areas to be repaired. So you can choose only those areas which you know are damaged thus saving flashing time.
To resurrect SE X8:

Solder JTAG cable to SE X8 JTAG pads;
Insert USB Data cable into board and PC;
Make sure SE X8 is selected in the list of models;
If you use only battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
http://www.jtagbox.com/wp-content/up..._xperia_x8.jpg

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

03.08.2011 Samsung Galaxy Tab M180s Unbrick – Boot Repair supported
Samsung M180S is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in some cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.


To resurrect Samsung M180S:
Solder JTAG cable to Samsung M180S JTAG pads;
Connect USB cable to phone and PC;
Attach battery connector;
Make sure Samsung M180S is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.



Bug fix update :

Samsung S5830
Improved resurrection by adding few more zones to be reflashed.
Fixed issue with NAND chip not being detected (0xAAAA/0xAAAA ID)
CPU ID 0x303C10E1 added to allowed list


Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


RIFF Box – JTAG Revolution

RIFF JTAG - JTAG Manager v1.35 released

04.08.2011 JTAG Manager v1.35 released

Whats new :

• Added an arbitrary feature “Settings by Code” to the DCC Read/Write page.

Main purpose is to improve support quality for users: via “Settings Code” string a supporter person sees all settings which were set by user on the DCC Read/Write page.
Though, end-user may benefit from this too: Use “Settings Code” string for JTAG Manager to automatically setup all DCC Read/Write settings

• Fixed data loss during read and save operations in case there is not enough disk space available to store required amount of data.

(for example reading full on DCC Read/Write page, or saving read full, etc).
Now available disk space checks are performed prior disk write operations.


Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


RIFF Box – JTAG Revolution

RIFF JTAG - JTAG Manager v1.35 released

04.08.2011 JTAG Manager v1.35 released

Whats new :

• Added an arbitrary feature “Settings by Code” to the DCC Read/Write page.

Main purpose is to improve support quality for users: via “Settings Code” string a supporter person sees all settings which were set by user on the DCC Read/Write page.
Though, end-user may benefit from this too: Use “Settings Code” string for JTAG Manager to automatically setup all DCC Read/Write settings

• Fixed data loss during read and save operations in case there is not enough disk space available to store required amount of data.

(for example reading full on DCC Read/Write page, or saving read full, etc).
Now available disk space checks are performed prior disk write operations.


Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


RIFF Box – JTAG Revolution

23.08.2011 Samsung Galaxy GIO (S5660) Unbrick – Boot repair supported


Samsung S5660 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.


To resurrect Samsung S5660 do this:

Solder JTAG cable to Samsung S5660 JTAG pads;
Insert battery and connect USB cable to phone and PC;
Make sure Samsung S5660 is selected in the list of models;
Click Resurrect button;
Wait few seconds until software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.


To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘OK’ keys and press Power-On to enter Download Mode;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution