RIFF JTAG -Samsung Update
10.01.2012 Samsung SGH-T759 Exhibit 4G Unbrick – Boot Repair supported
Added support for Samsung SGH-T759 Exhibit 4G
Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.
RIFF Box – JTAG Revolution
RIFF JTAG – HTC Inspire 4G A9192 (HTC Stallion) Unbrick, Boot, IMEI, CID, ModelID, Unlock supported
HTC Inspire 4G A9192 (HTC Stallion) Unbrick, Boot, IMEI, CID, ModelID, Unlock supported
Resurrecting HTC Inspire is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Inspire boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 0.85.0024. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD9812000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.
To resurrect HTC Inspire:
* Solder JTAG cable to HTC Inspire JTAG pads;
* Insert batter and connect USB Data cable;
* Make sure HTC Inspire is selected in the list of models;
* If you use only battery, press Power On key;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
To enter download mode:
* Disconnect PC cable;
* Insert battery;
* Hold ‘Volume Down’ key and press ‘Power ON’ button.
http://www.jtagbox.com/wp-content/up...inspire_4g.jpg
RIFF JTAG – HTC Panache/Glacier/My Touch 4G Unbrick, IMEI, CID, ModelID, Unlock supported
HTC Panache/Glacier/My Touch 4G Unbrick, IMEI, CID, ModelID, Unlock supported
Resurrecting HTC Glacier is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Glacier boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM7230 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write SPL version 0.86.0000. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD1510000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.
To resurrect HTC Glacier:
* Solder JTAG cable to HTC Glacier JTAG pads;
* Insert batter and connect USB Data cable;
* Make sure HTC Glacier is selected in the list of models;
* If you use only battery, press Power On key;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
To enter download mode:
* Disconnect PC cable;
* Insert battery;
* Hold ‘Volume Down’ key and press ‘Power ON’ button.
_
http://www.jtagbox.com/wp-content/up...tc_panache.jpg
RIFF JTAG – Samsung Galaxy Precedent SCH-M828 Unbrick supported
09.02.2012 Samsung Galaxy Precedent SCH-M828 Unbrick supported
Samsung M828 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.
To resurrect Samsung M828 do this:
Solder JTAG cable to Samsung M828 JTAG pads;
Insert battery and connect USB cable to phone and PC;
Make sure Samsung M828 is selected in the list of models;
Click Resurrect button;
Wait few seconds until software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On to enter Download Mode;
http://www.jtagbox.com/wp-content/up...nt-M828C-c.jpg
RIFF JTAG-HTC ThunderBolt 4G ADR6400 (HTC Mecha) Unbrick – Boot repair supported
14.02.2012 HTC ThunderBolt 4G ADR6400 (HTC Mecha) Unbrick – Boot repair supported
14.02.2012 HTC ThunderBolt 4G ADR6400 (HTC Mecha) Unbrick – Boot repair supported
14.02.2012 HTC ThunderBolt 4G ADR6400 (HTC Mecha) Unbrick – Boot repair supported
Resurrecting HTC Thunderbolt CP (Modem Part) part is easy.
Phone is auto powered on with USB Data Cable connected to the PC while battery is inside; sometimes during connection pressing Power On key may be required.
Please note, CP Part’s power is controlled by the AP Part, thus you may experience constant connection loses after definite ammounts of time (1-2-5-x seconds). If this keeps interferring the resurrection process, solder additionall JTAG interface cable to the AP pads, select AP resurrector DLL, go to the JTAG Read/Write page and halt AP core, then switch back to the CP JTAG interface.
To resurrect HTC Thunderbolt CP (Modem Part) Part:
Solder JTAG cable to HTC Thunderbolt CP JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC Thunderbolt CP is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
Resurrecting HTC Thunderbolt AP (PDA Part) is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.04.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG0510000’.
There is option to reflash BOOT and RECOVERY zones.
_
Bug Fix
HTC_DesireS.dll
-------------------------------------
- ID 0x27B360E1 is added to allowed list
HTC_Supersonic.dll
-------------------------------------
- added resurrection data for 4Kb NAND chips, so now DLL has data for both 4KB and 2KB versions.
Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.
RIFF Box – JTAG Revolution