RIFF JTAG – T-Mobile Samsung SGH-T989 Galaxy S II Unbrick – Dead Boot Repair supported, World First ! ! !
14.03.2012 RIFF JTAG – T-Mobile Samsung SGH-T989 Galaxy S II Unbrick – Dead Boot Repair supported, World First ! ! !
Repairing bricked Samsung T989 is easy with the RIFF Box. The device is based on the Qualcomm APQ8060 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
To resurrect Samsung T989:
Solder JTAG cable to Samsung T989 JTAG pads;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung T989 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press Power-On.
.
http://www.jtagbox.com/wp-content/up...i_hercules.jpg
RIFF JTAG – Samsung SGH-i727 Galaxy S II Skyrocket Unbrick – Dead Boot Repair, World First ! ! !
14.03.2012 RIFF JTAG – Samsung SGH-i727 Galaxy S II Skyrocket Unbrick – Dead Boot Repair, World First ! ! !
Repairing bricked Samsung I727 is easy with the RIFF Box. The device is based on the Qualcomm APQ8060 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
To resurrect Samsung I727:
Solder JTAG cable to Samsung I727 JTAG pads;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung I727 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press Power-On.
http://www.jtagbox.com/wp-content/up..._skyrocket.jpg
RIFF JTAG – HTC EVO 3D (HTC Shooter) Unbrick – Boot Repair Supported, World First ! ! !
14.03.2012 RIFF JTAG – HTC EVO 3D (HTC Shooter) Unbrick – Boot Repair Supported, World First ! ! !
Repairing bricked HTC EVO 3D (PG86300) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 1.49.0007. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG8630000’.
There is option to reflash BOOT and RECOVERY zones.
To resurrect HTC EVO 3D:
Solder JTAG cable to HTC EVO 3D JTAG pads;
Insert batter and connect USB Data cable;
Make sure HTC EVO 3D is selected in the list of models;
If you use only battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button.
.
http://www.jtagbox.com/wp-content/up...c_evo_3d_4.jpg
RIFF JTAG - WANTED ! ! ! HUAWEI Models ! ! !
Hello dear RIFF Box users !
Time to time we need help from our users, in order to improve our support and increase list of supported devices.
In this topic I'll post wanted stuff, so users who provide help here will have priority when they need support.
15.03.2012 Important - RIFF Box HUAWEI Phones Support
Wanted following Huawei Models:
* U8110 (Dead)
* U8120 (Dead)
* U8150(Dead)
* U8230(Dead)
* U8300 (Dead)
* U8510 (Dead)
* U8650 (Working)
* U8800 (Working)
* U8860 (Working)
* Any other Huawei model
If You have any of above mentioned models, please contact me via ICQ or Sonork for further steps.
Dead phones needed for beta tests :
* Samsung T589
* LG E510
Working phone full dumps :
* LG E510
Phones needed in Ukraine, Kiev :
Any HTC Model, based on QUALCOMM MSM82xx CPU, in QHUSB_DLOAD mode (Error 0X44 on JTAG)
List of models:
* HTC Desire HD
* HTC Desire S
* HTC Desire Z
* HTC Sensation
* HTC Inspire
* Any other model based on MSM8255, MSM8260
Any Samsung model (Working or Bricked), based on QUALCOMM APQ8060 CPU
List of models:
* Samsung i717
* Samsung E160S
* Samsung E110s
PCB Photos we need :
* Any of not supported model !
Photos must be made in high resolution, if possible on daylight, without use of flash or artificial light.
Good photo sample :
http://www.jtagbox.com/downloads/man...7_3_sample.jpg
RIFF JTAG – HTC EVO View 4G Unbrick, Unlock, IMEI and CID update supported
19.03.2012 RIFF JTAG – HTC EVO View 4G Unbrick, Unlock, IMEI and CID update supported
Repairing bricked HTC EvoView4G is easy using RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Some (or all) revisions of HTC EvoView4G boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM8255 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL to 1.38.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG4120000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.
To resurrect HTC EvoView4G:
*Solder JTAG cable to HTC EvoView4G JTAG pads;
*Insert battery and connect USB Data cable;
*Make sure HTC EvoView4G is selected in the list of models;
*If you use only battery, press Power On key;
*Click Resurrect button;
*Wait till software signals a successful operation completion;
*Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
To enter download mode:
*Disconnect PC cable;
*Insert battery;
*Hold ‘Volume Down’ key and press ‘Power ON’ button.
http://www.jtagbox.com/wp-content/up...vo_view_4g.jpg
27.03.2012 RIFF JTAG – Samsung SCH-I500 Galaxy S Mesmerize/Fascinate Unbrick Supported
Repairing bricked Samsung SCH-I500 Galaxy S Mesmerize/Fascinate is easy with RIFF Box.
I500 is based on the S5PCxxx Processor (ARM core is Cortex-A8). Please note the adaptive clocking mode (RTCK) is not available on this processor, so make sure to select a fixed TCK frequency.
To establish the JTAG connection attach battery cable and press Power On key.
In case after resurrection the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.
To resurrect Samsung I500:
Solder JTAG cable to Samsung I500 JTAG pads;
Attach battery cable and press Power On key;
Make sure Samsung I500 is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
http://www.jtagbox.com/wp-content/up..._mesmerize.jpg
