RIFF BOX JTAG New Update AE Post ở đây

[TuấnPhát_GSM]

Repairing bricked HTC Flyer WiFi (PG41400) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Some (or all) revisions of HTC Flyer boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM8255 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the DBL loader, so writing to DBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into DBL zone and will respond with success code as if flashing succeeded. In this way DBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except DBL area) and will re-write PDA’s SPL to 1.11.0011 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG4140000’.
There is option to reflash android BOOT and RECOVERY zones. Recovery zone is flashed with ClockworkMod Recovery 4.0.1.4. In addition, you can set S-OFF (unlock HBOOT so you will be able to flash any ROM) by selecting S-OFF HBOOT version in the resurrector settings.
Sometimes (for example after rooting attempts) phone has a modified DBL loader (which may not accept official HTC boot files). To restore phone functionality you need to reflash DBL loader. There is option to reflash DBL code (DBL area will be temporary unlocked for reflashing). But please note, reflashing DBL area is very dangerous, since in case flashing stops in the middle, you will have briked phone with permanently disabled JTAG interface.
Please note, if your phone has the DBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Flyer WiFi:

Solder JTAG cable to HTC Flyer JTAG pads;
Insert battery and connect USB Data cable;
Make sure HTC Flyer (PG41400) is selected in the list of models;
If you use only battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods. You can use CWM recovery to flash any ZIP file – for this during resurrection add BOOT & RECOVERY zones to be resurrected too.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button.

[TuấnPhát_GSM]

24.04.2012 RIFF JTAG – HTC via USB Cable Support added


Whats new:

Released support for HTC phones based on MSM8x55 CPU, which are enumerated on USB port as “QHUSB_DLOAD” device. Now it’s possible to repair these phones without soldering any wires. Even without opening !

Following models are supported at the moment:

HTC Desire HD (HTC Ace)
HTC Desire S (HTC Saga)
HTC Desire Z (HTC Vision)
HTC Flyer 3G
HTC Flyer WiFi
HTC Evo View 4G

It is possible to force QHUSB_DLOAD mode by disabling Vdd line on eMMC chip. Check Desire S TP info for example. This means, You can work with any MSM8255/MSM8655 based HTC phone, as long as You force it into QHUSB_DLOAD mode.
Follow this procedure if You want to use these updates:

*Connect Your phone to USB port and install QHUSB_DLOAD device driver (C:\Program Files (x86)\RIFF Box JTAG Manager\Drivers\32Bit\QDLOADER)
*Launch JTAG Manager, select appropriate Model DLL and click desired button
*Install “RIFF Box DCCLoader USB Interface” port driver (C:\Users\Admin\Desktop\Drivers_64Bit_WorkedForMe\ Drivers\64Bit\DCCLDR)
*If req

uired, repeat the procedure (sometimes required if device is connected for first time)

We will release USB support for rest of the models on these CPU-s in following days.
To download and install new updates – simply click “Check for Updates” button on Box Service TAB.

[HoangThong_hotrokythuat4]

03.08.2010 Huawei E1550 Modem

Please download new "Huawei_E1550.dll". There was bug with repair pack, and now its fixed.

[HoangThong_hotrokythuat4]

03.08.2010 HTC Dream Google G1 Unbrick, Unlock, IMEI repair.

Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL-s, download it and restart the software.
“HTC_Dream.dll” contains pinout, repair instructions and required repair files for HTC Dream Google G1 Unbrick, Unlock and IMEI repair.

[HoangThong_hotrokythuat4]

03.08.2010 RIFF JTAG – HTC Topaz – Diamond2 Unbrick, Unlock, IMEI repair.
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL-s, download it and restart the software.
“HTC_Topaz.dll” contains pinout, repair instructions and required repair files for HTC Topaz – Diamond2 Unbrick, Unlock, IMEI repair.

[HoangThong_hotrokythuat4]

04.08.2010 ZTE MF627 Modem Unbrick dead boot repair supported
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL-s, download it and restart the software.
“ZTE_MF626.dll” contains pinout, repair instructions and required repair files for ZTE MF626, MF627 Modem dead boot repair.

[HoangThong_hotrokythuat4]

04.08.2010 RIFF JTAG – Samsung S5560 dead boot repair
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL-s, download it and restart the software.
“Samsung_s5560.dll” contains pinout, repair instructions and required repair files for Samsung S5560 dead boot repair.

[HoangThong_hotrokythuat4]

06.08.2010 RIFF JTAG – HTC Herald Unbrick, dead boot repairPlease start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL-s, download it and restart the software.“HTC_Herald.dll” contains pinout, repair instructions and required repair files for HTC Herald Unbrick, dead boot repair.

[HoangThong_hotrokythuat4]

06.08.2010 RIFF JTAG – Toshiba G810 Unbrick, dead boot repair
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL-s, download it and restart the software.
“Toshiba_G810.dll” contains pinout, repair instructions and required repair files for Toshiba G810 Unbrick, dead boot repair

[HoangThong_hotrokythuat4]

06.08.2010 RIFF JTAG – Samsung i8510 unbrick, dead boot repair
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL-s, download it and restart the software.
“Samsung_i8510_modem.dll” contains pinout, repair instructions and required repair files for Samsung i8510 unbrick, dead boot repair.