Hướng dẫn sử dụng S-Card, Smart-Clip + SmartMoto

[saigonmobile]

Hướng dẫn sử dụng S-Card, Smart-Clip + SmartMoto


S-Card, Smart-Clip + SmartMotoAs soon as S-Card dongle and Smart-Clip are connected to PC, SmartMoto is ready to operate.

Before starting SmartMoto, please set the compatibility for corresponding Operating System (right click on SM.exe file and choose Properties > Compatibility…)

To run SmartMoto under Win2000/XP and to update Smart-Clip, please launch SM, open bookmark "Smart –Clip" and tick the option "Disable OS parallel port polling (requires reboot)".

After that – PC requires to be restarted.

Flash file formats SmartMoto supports 5 flash file formats (4 of them are new to Smart-Clip): *.mfw, *.mbk, *.pcf, *.sbf and *.shx. No other formats will be compatible.

WARNING:
*.smf and *.smb files will be supported by SmartMoto version 1.23, Smart-Clip version 2.26 and lower versions only.

*.mfw - are meant to be used when the handset is connected to PC via Smart-Clip

Connect handset to PC via Smart-Clip (phone > USB cable > Smart-Clip > LPT cable > PC).
Connect S-Card to PC USB port.
Connect power supply to Smart-Clip and power on the handset.
Launch SmartMoto.
Choose "Smart-Clip USB port" in phone connection field.
Press "Search". Software should perform the following steps:
SmartMoto detects S-Card;
SmartMoto detects Smart-Clip;
SmartMoto detects the handset and reads phone information.
Log to bookmark "Flash".
Press "Browse" to select the flash file.
Press "Write flash".
Message "Flash completed" appears at the end of the process.
There are 3 types of *.mfw flash files

reflash.mfw - meant to be used for upgrade of software. No data will be lost from the phone. Other words, all downloaded pictures, ring tones, contacts won't be erased from the handset memory.
flash_flex.mfw - meant to be used for upgrade of software with change of flex (change of basic setting, e.g. working frequency band). Some data could be lost from the phone's memory after flashing.
full_flash.mfw - complete change of firmware including the EEPROM. All added data will be erased from the memory.
Flash optionsForce simple write mode (slower)

Sometimes during work with different types of flash memory chips, Block record method does not work.

In this case it's possible to work with slower but easier and more reliable flashing method - "word" flashing method. Such method takes up to 3-4 times longer to flash, but allows to work with wider variety of microchips. We recommend using this method in case of problems with block method.

Overwrite boot area

This option is required for flashing the handset with full_flash.mfw file while boot core has to be repaired or changed (downgraded).

Skip firmware mismatch confirmation

In some cases, the handset can be flashed with higher lang_pack version that differs from the original phone firmware. This option allows to avoid the firmware check. (Recommended for advanced users only!)

Turn phone off after flashing

This option allows the SmartMoto turning the handset off right after the flash process finished.

Full Flash backup*.mbk - flash backup created with Smart-Clip, S-Card together with SmartMoto.

Connect handset to PC via Smart-Clip (phone > USB cable > Smart-Clip > LPT cable > PC).
Connect S-Card to PC USB port.
Connect power supply to Smart-Clip and power on the handset.
Launch SmartMoto.
Choose "Smart-Clip USB port" in phone connection field.
Press "Search". Software should perform the following steps:
SmartMoto detects S-Card;
SmartMoto detects Smart-Clip;
SmartMoto detects the handset and reads phone information.
Log to bookmark "Backup".
Press "Backup phone flash".
Select the location for the file to be saved.
Message "file.mbk saved" appears when the process is completed.
The handset can be also flashed with a file backed up from another phone. In some models security zone will get backed up automatically with the flash file. In this case, after flashing the phone the original security area has to be restored:

Connect handset to PC via Smart-Clip (phone > USB cable > Smart-Clip > LPT cable > PC).
Connect S-Card to PC USB port.
Connect power supply to Smart-Clip and power on the handset.
Launch SmartMoto.
Choose "Smart-Clip USB port" in phone connection field.
Press "Search". Software should perform the following steps:
SmartMoto detects S-Card;
SmartMoto detects Smart-Clip;
SmartMoto detects the handset and reads phone information.
Log to bookmark "Backup".
Press "Browse" to select the flash backup created from another handset.
Press "Restore phone flash".
Wait until the process completes.
Press "Browse" button again.
Select the original PDS backup (can be recognized by phone’s IMEI).
Press "Restore security area".
The handset is ready for operation.
In any case do not overwrite security area with the security file from another handset.

We strictly recommend not to flash the phones with backup flash files received from other phones in these models: C975, C980, V975, V980, E1000, A1000, V1050. We would urge everyone to use the latest version of SmartMoto and to flash the handsets only with files downloaded from our website. This does not apply to the backed up language packs.

Please, create a backup of the full flash before actual flashing. So, in case of the wrong flashing the handset can be restored to its original state.

Backup files (*.mbk) are created only for the Clip that they were made with.

It’s not possible to use "restore" feature with the backup file made by any other Clip.

In case of creating a backup of language pack, file will be saved in *.mfw format and won’t be bound to Smart-Clip hardware.

[saigonmobile]

tiếp theo ...


Backup of language pack

This option allows to creating a copy of language package only, when the full backup is not required.

Connect handset to PC via Smart-Clip (phone > USB cable > Smart-Clip > LPT cable > PC).
Connect S-Card to PC USB port.
Connect power supply to Smart-Clip and power on the handset.
Launch SmartMoto.
Choose "Smart-Clip USB port" in phone connection field.
Press "Search". Software should perform the following steps:
SmartMoto detects S-Card;
SmartMoto detects Smart-Clip;
SmartMoto detects the handset and reads phone information.
Log to bookmark "Flash".
Press "Read language pack".
Select the location for the file to be saved.
Message "Reading language pack done" appears when the process is completed.
During Read Flash procedure - flash files will be created in safe mode ensuring quality flashing later. If there is a risk that firmware can’t be read safely, SmartMoto will not complete the Read Flash procedure

PC flash*.pcf – flash file to be used in PC flash mode of SmartMoto program with S-Card connected to PC USB port. No Smart-Clip is required in this case.

Connect the handset to PC USB port.
Connect S-Card to PC USB port.
Launch SmartMoto.
Choose "Computer USB port" in phone connection window.
Press "Search". Software should perform the following steps:
SmartMoto detects S-Card;
SmartMoto detects the handset and reads all information.
Log to bookmark "PC Flash".
Press "Browse" to select the flash file.
Press "Write flash".
Message "Flash completed" informs on the end of the process.
Note:
Flashing in PC flash mode requires a phone driver to be installed. Universal driver for all P2K models is available within SmartMoto directory (SmartMoto install folder \drivers\p2k.sys). To install the driver: connect your handset to the PC, system will detect a new device, locate the driver and run the installation as many times as system will require it.

*.sbf /*.shx – original manufacturer flash file formats to be used in PC flash mode (see *.pcf file description.

UnbrandingIf the phone model is supported and there is available an unbranded flash file or the model with unbranded firmware – the handset can be simply unbranded by flashing it with unbranded firmware.

Don't forget to restore the original security zone (Restore security area) after flashing with backup file if needed.

PDS zone problem descriptionHandset does not turn on, gets detected in SmartMoto, full flashing does not help. Possible problems: hardware or software.

SmartMoto can not fix any hardware problem

Software: Among the few reasons there could be corrupted PDS zone.

Similar to Flashing, "Repair PDS" can be performed only if the handset gets detected by SmartMoto.

"Repair PDS" option requires a constant Internet connection with Smart-Clip server. Internet settings must be the same as for Smart-Clip update.

Connect handset to PC via Smart-Clip (phone > USB cable > Smart-Clip > LPT cable > PC).
Connect S-Card to PC USB port.
Connect power supply to Smart-Clip and power on the handset.
Launch SmartMoto.
Choose "Smart-Clip USB port" in phone connection field.
Press "Search". Software should perform the following steps:
SmartMoto detects S-Card;
SmartMoto detects Smart-Clip;
SmartMoto detects the handset and reads phone information.
Log to bookmark "Repair".
Select the phone model from the scrolling list of supported for that operation models.
Press "Repair PDS".
Message "Please write a corresponding full_flash file to phone to accomplish repair" informs of successful complete of the first stage of the process.
Log to bookmark "Flash".
Press "Browse" to select an appropriate full_flash file.
Press "Write flash".
"Flash completed" message informs on finish of the repair process.
Disconnect the handset, it’s ready for use.
WARNING
Before performing "Repair PDS" procedure, please make sure the model is included into the list and select it very carefully. In case if the model is not listed – do not perform repair procedure, otherwise it will seriously harm the handset. So, even restore of full original backup will not fix it.

For the phone models marked with asterisk (*), use a TestPoint connection method. Detailed description of TestPoint connection method is located at Support section.

Section repair PDS has an option "Quick model find" for fast search of the model on the list. Selected model is marked by a triangle. Just enter phone model in "Quick model find" window and program will automatically find it in the list.

We strictly recommend making a full backup from the phone before performing a "Repair PDS" procedure.

Frequency band switchingConnect handset to PC via Smart-Clip (phone > USB cable > Smart-Clip > LPT cable > PC).
Connect S-Card to PC USB port.
Connect power supply to Smart-Clip and power on the handset.
Launch SmartMoto.
Choose "Smart-Clip USB port" in phone connection field.
Press "Search". Software should perform the following steps:
SmartMoto detects S-Card;
SmartMoto detects Smart-Clip;
SmartMoto detects the handset and reads phone information.
Log to bookmark "Service".
Select a required value in "Operation band" field.
Press "Update band".
Disconnect the handset, after the process is completed.
The phone is set to the new operation band.
Note
Reset of the phone frequency is possible only if the handset hardware allows to do so. It might happen that the process of band changing was successfully completed but after switching the phone off and turning it back on, the band automatically changes to the default one. This means that phone’s hardware does not support customer settings.

Other service optionsActivate phone "Java App Loader" option – activates the Java applet in the phone menu.
Reset phone Life Timer - returns phone life timer back to "0" (zero).
Master Reset - resets all customer settings to default factory settings.
Master Clear - clears all customer data.
Enable Unicode – option allows setting the phone to receive SMS in Unicode.
Set subsidy code to "00000000" – after connecting the phone, using a "TestPoint connection" method and flashing with a branded flash file, the handset may require a subsidy code to be entered. It is recommended to set the code value to "00000000" (eight times zero) before actual flashing – thus the user will be able to enter it when the SIM-card is inserted into the phone. If the code has not been reset to "00000000" (eight times zero) the handset will require unlock procedure to be performed in this case.
Battery settings – for best phone performance is recommended to create backup of the battery settings before performing a flash operation and restore them after completing the flash.

SmartMoto & phone unlockingUse of SmartMoto is required for unlock process if the phone boot version is: 6.12, 6.31, 6.36, 6.71, 6.82, 8.26, 8.A0, 8.A1, 8.D0, A.02, A.30 and higher.

[donghomatkinh]

hay quá...có ai dịch ra tv dùm với

[BlachThon]

Đọc thì chưa hiểu hết vấn đề đâu , nhưng có tài liệu là tốt rồi
thanks ác min

[xuanson77]

Mấy huynh ơi em có SmartMoto, V1.23, Firmwave 2.26 có nâng cấp ver được không?. Em update thì nó đòi S-card. Em chưa có S-card, nếu mua thì mua ở đâu vậy? giá bao nhiêu vậy anh>Thấy giới thiệu thì cũng thích thật.

[habinhthuan]

Mấy huynh ơi em có SmartMoto, V1.23, Firmwave 2.26 có nâng cấp ver được không?. Em update thì nó đòi S-card. Em chưa có S-card, nếu mua thì mua ở đâu vậy? giá bao nhiêu vậy anh>Thấy giới thiệu thì cũng thích thật.

Nâng cấp đc, u vào www.smart-clip.com xem, S-card chuẩn bị có rồi đó.

[hieuhanh11]

tròi oi!a có hướng dẫn sử dụng tiếng việt ko????

[hoang_tuan968]

có hdẫn tviệt thì tuyệt vời biết mấy các bác nhỉ!!!!!!!!!!

[mr_bin]

các bạn đợi đi nha, mình đang đi học khóa anh văn cấp tốc

[hungsun_mobile]

cám ơn anh admin rất nhiều,may mình cũng biết một ít tiếng anh kô thì khó khăn đây......hiiiiiiiiiiii!
thank anh một lần nữa