[Chia sẻ] Best Tool Infinity free carck

[buican]

Cái này thấy bên vietfones có Post rồi,bên đây chưa có nên em post lên cho ace nào ai muốn tay không bắt cướp thì đem về dùng, ace nào có rồi đừng chém em, em chỉ muốn chia sẻ thôi.
vừa đem con 6233 ra làm chuột bạch kết quả ok ngọt như mía

Tải ở đây

[QUANGTRUNG_GSM]

tes done ae cứ múc thoải mái nhé chạy qua ufs


DLL not found...
BB5 Easy Service Tool v1.14.1 (c) Infinity-Box Team Ready

Connect phone on selected interface...

UFS S/N 79577 boot - Ok

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok

Read and Check phone data...
Infineon checking...

SIMLOCK TEST : Ok
RUN TEST : Ok

Booting phone now....
Sync Ok , A2
CPU ID : XGOLD , A200341100
Boot Ok , 01
PBL : SE0_091125 F11
Algo Ok , 01
SBL mode Ok
SBL : Default_RAM_Bootloader
EPP CFG [Bering]...
FLASH ID : 0020000000C08800
FLASH ID : ST, M58WR064
Boot Done!


Done!

Connect phone on selected interface...

Selected FlashSettings : Manual
-> File : rh105_05.710 not found! Check it!
-> File : rh105_05.71mr not found! Check it!
-> File : rh1050_nai5.71mr not found! Check it!
Files Set for Flashing :

Flash files not selected!!! Break...

Phone found!
Series 40 Device detected!
read info... - Ok

Selected FlashSettings : Manual
Files Set for Flashing :
MCU : rh105_05.710
PPM : rh105_05.71mr
CNT : rh1050_nai5.71mr
File damaged or Unknow format...
File damaged or Unknow format...
File damaged or Unknow format...
Check FlashFiles, Please, wait...
Bad file : rh105_05.710
Bad file : rh105_05.71mr
Bad file : rh1050_nai5.71mr
Bad Flash files detected, will break procedure

Selected FlashSettings : Manual
Files Set for Flashing :
MCU : rm647_003.600
PPM : rm647_003.60mr
CNT : rm6470_nai03.60mr

Infineon flashing...
Booting phone now....
Sync Ok , A2
CPU ID : XGOLD , A200341100
Boot Ok , 01
PBL : SE0_091125 F11
Algo Ok , 01
SBL mode Ok
SBL : Default_RAM_Bootloader
EPP CFG [Bering]...
FLASH ID : 0020000000C08800
FLASH ID : ST, M58WR064
Boot Done!

===Flashing [MCU]===
File : rm647_003.600
Image : hw_b2_rm647_r03.600.fls
Cert block found, sending....
Cert sent
Found 3 region(s)
Processing Region 1/3
Erase , Start : 0x00800000 , Len : 0x00210000
Erasing, wait ...
Erase done
Write , Start : 0x00800000 , Len : 0x00210000
Flashing , wait ...
Region flash done
Processing Region 2/3
Erase , Start : 0x00C60000 , Len : 0x001E8840
Erasing, wait ...
Erase done
Write , Start : 0x00C60000 , Len : 0x001E8840
Flashing , wait ...
Region flash done
Processing Region 3/3
Erase , Start : 0x00FFC000 , Len : 0x00000040
Erasing, wait ...
Erase done
Write , Start : 0x00FFC000 , Len : 0x00000040
Flashing , wait ...
Region flash done
Check : 4445
===Flashing [PPM]===
File : rm647_003.60mr
Image : hw_b2_rm647_003.60mr.fls
Cert block found, sending....
Cert sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x00210000 , Len : 0x00118700
Erasing, wait ...
Erase done
Write , Start : 0x00210000 , Len : 0x00118700
Flashing , wait ...
Region flash done
Check : 5870
===Flashing [CNT]===
File : rm6470_nai03.60mr
Image : hw_b2_rm6470_nai03.60mr.fls
Cert block found, sending....
Cert sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x00EB0000 , Len : 0x0004C5C0
Erasing, wait ...
Erase done
Write , Start : 0x00EB0000 , Len : 0x0004C5C0
Flashing , wait ...
Region flash done
Check : 86E6

Flashing done, rebooting...
-> Infineon info : Do FullFactory Sets after flashing
Flashing Done!

Init Service mode... Wait...

Afterflash settings...
SW ver : V 03.60
01-04-10
RM-647
(c) Nokia
IMEI : 352404055364689
PCode : 0593211
All done!

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok

[manhdung81mobile]

tes done ae cứ múc thoải mái nhé chạy qua ufs


DLL not found...
BB5 Easy Service Tool v1.14.1 (c) Infinity-Box Team Ready

Connect phone on selected interface...

UFS S/N 79577 boot - Ok

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok

Read and Check phone data...
Infineon checking...

SIMLOCK TEST : Ok
RUN TEST : Ok

Booting phone now....
Sync Ok , A2
CPU ID : XGOLD , A200341100
Boot Ok , 01
PBL : SE0_091125 F11
Algo Ok , 01
SBL mode Ok
SBL : Default_RAM_Bootloader
EPP CFG [Bering]...
FLASH ID : 0020000000C08800
FLASH ID : ST, M58WR064
Boot Done!


Done!

Connect phone on selected interface...

Selected FlashSettings : Manual
-> File : rh105_05.710 not found! Check it!
-> File : rh105_05.71mr not found! Check it!
-> File : rh1050_nai5.71mr not found! Check it!
Files Set for Flashing :

Flash files not selected!!! Break...

Phone found!
Series 40 Device detected!
read info... - Ok

Selected FlashSettings : Manual
Files Set for Flashing :
MCU : rh105_05.710
PPM : rh105_05.71mr
CNT : rh1050_nai5.71mr
File damaged or Unknow format...
File damaged or Unknow format...
File damaged or Unknow format...
Check FlashFiles, Please, wait...
Bad file : rh105_05.710
Bad file : rh105_05.71mr
Bad file : rh1050_nai5.71mr
Bad Flash files detected, will break procedure

Selected FlashSettings : Manual
Files Set for Flashing :
MCU : rm647_003.600
PPM : rm647_003.60mr
CNT : rm6470_nai03.60mr

Infineon flashing...
Booting phone now....
Sync Ok , A2
CPU ID : XGOLD , A200341100
Boot Ok , 01
PBL : SE0_091125 F11
Algo Ok , 01
SBL mode Ok
SBL : Default_RAM_Bootloader
EPP CFG [Bering]...
FLASH ID : 0020000000C08800
FLASH ID : ST, M58WR064
Boot Done!

===Flashing [MCU]===
File : rm647_003.600
Image : hw_b2_rm647_r03.600.fls
Cert block found, sending....
Cert sent
Found 3 region(s)
Processing Region 1/3
Erase , Start : 0x00800000 , Len : 0x00210000
Erasing, wait ...
Erase done
Write , Start : 0x00800000 , Len : 0x00210000
Flashing , wait ...
Region flash done
Processing Region 2/3
Erase , Start : 0x00C60000 , Len : 0x001E8840
Erasing, wait ...
Erase done
Write , Start : 0x00C60000 , Len : 0x001E8840
Flashing , wait ...
Region flash done
Processing Region 3/3
Erase , Start : 0x00FFC000 , Len : 0x00000040
Erasing, wait ...
Erase done
Write , Start : 0x00FFC000 , Len : 0x00000040
Flashing , wait ...
Region flash done
Check : 4445
===Flashing [PPM]===
File : rm647_003.60mr
Image : hw_b2_rm647_003.60mr.fls
Cert block found, sending....
Cert sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x00210000 , Len : 0x00118700
Erasing, wait ...
Erase done
Write , Start : 0x00210000 , Len : 0x00118700
Flashing , wait ...
Region flash done
Check : 5870
===Flashing [CNT]===
File : rm6470_nai03.60mr
Image : hw_b2_rm6470_nai03.60mr.fls
Cert block found, sending....
Cert sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x00EB0000 , Len : 0x0004C5C0
Erasing, wait ...
Erase done
Write , Start : 0x00EB0000 , Len : 0x0004C5C0
Flashing , wait ...
Region flash done
Check : 86E6

Flashing done, rebooting...
-> Infineon info : Do FullFactory Sets after flashing
Flashing Done!

Init Service mode... Wait...

Afterflash settings...
SW ver : V 03.60
01-04-10
RM-647
(c) Nokia
IMEI : 352404055364689
PCode : 0593211
All done!

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok

bác hướng dẫn cụ thể chạy bằng USB đi
em lấy 3110c ra làm chuột bạch kết quả ngủ luôn

[Quoc12]

sao không hướng dẩn cụ thể a cho a e biết

[QUANGTRUNG_GSM]

sao không hướng dẩn cụ thể a cho a e biết

chọn qua ufs nhé bạn như hình [IMG][/IMG]

trời ơi imei đẹp quá trời

lôi con 6300 ra chạy qua ufs nhé bạn kết quả done

DLL not found...
BB5 Easy Service Tool v1.14.1 (c) Infinity-Box Team Ready

Connect phone on selected interface...

UFS S/N 79577 boot - Ok

Connect phone on selected interface...

Selected FlashSettings : Manual
Files Set for Flashing :
MCU : rm217__07.21.mcusw
PPM : rm217__07.21.ppm_v
CNT : rm217__07.21.image_v_black
Check FlashFiles, Please, wait...
-> SWversion check skipped : Dead mode selected

Backup enabled, Will read Certificates now...
Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info :
CMT ASICID : 000000010000022600010006010C192101001101
CMT EM0 ID : 00000232
CMT EM1 ID : 00000353
CMT PUB ID : 19E000193C267E565B012E4A9ED7115EE71B8D77
CMT MODE ID : 00
CMT R_HASH : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID : 191EC665DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg
CMT Loader sent, Boot Ok
MCU Configuration
FLASHID : 220800EC , CMT , NOR
CMT Flash ID : 220800EC < SAMSUNG [SEC] => K8F5615ETM\K5G5629ATD
FLCNT : 00000000000000000000000000000000000000
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo.fg
CMT Algo sent
CMT PAPUB : 7E6491E8D30494B45630BB3A8599F4E1C674C95500
Transmission mode : Dual (Ddr, TX2)

Boot Done!

CMT : Read NPC certificate...
Cert size : 12288 byte(s)
IMEI : 359317025905220
CMT : Read CCC certificate...
Cert size : 8192 byte(s)
CMT : Read HWC certificate...
Cert size : 12288 byte(s)
CMT : Read VARIANT certificate...
Cert size : 20480 byte(s)
Cert Read done!

Init Service mode... Wait...

Init Service Mode Failed!
NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...

RPL saved : C:\Documents and Settings\Admin\Desktop\BEST infinity\BEST infinity\Backup\Cert\359317025905220_CRT.rpl

Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info :
CMT ASICID : 000000010000022600010006010C192101001101
CMT EM0 ID : 00000232
CMT EM1 ID : 00000353
CMT PUB ID : 19E000193C267E565B012E4A9ED7115EE71B8D77
CMT MODE ID : 00
CMT R_HASH : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID : 191EC665DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg
CMT Loader sent, Boot Ok
MCU Configuration
FLASHID : 220800EC , CMT , NOR
CMT Flash ID : 220800EC < SAMSUNG [SEC] => K8F5615ETM\K5G5629ATD
FLCNT : 00000000000000000000000000000000000000
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo.fg
CMT Algo sent
CMT PAPUB : 7E6491E8D30494B45630BB3A8599F4E1C674C95500
Transmission mode : Dual (Ddr, TX2)

Boot Done!

Transmission mode : Dual (Ddr, TX2)
Erase : Processing rm217__07.21.mcusw
Found 9 areas to erase, erase group
Asic : CMT , Sub : NOR
CMT , NOR , Area : 0x00000000 - 0x000006BF
CMT , NOR , Area : 0x000006C0 - 0x0001FFFF
CMT , NOR , Area : 0x00020000 - 0x0007FFFF
CMT , NOR , Area : 0x00080000 - 0x000DFFFF
CMT , NOR , Area : 0x00100000 - 0x001FFFFF
CMT , NOR , Area : 0x00200000 - 0x0031FFFF
CMT , NOR , Area : 0x00320000 - 0x0105FFFF
CMT , NOR , Area : 0x01060000 - 0x01067FFF
CMT , NOR , Area : 0x01068000 - 0x0107FFFF
Using TimeOut : 5 min ( 300 sec )
Erasing, wait.....
Erase error! Conection lost
Error on Erasing Phone!
Error...

Connect phone on selected interface...

Selected FlashSettings : Manual
Files Set for Flashing :
MCU : rm217__07.21.mcusw
PPM : rm217__07.21.ppm_v
CNT : rm217__07.21.image_v_black
Check FlashFiles, Please, wait...
-> SWversion check skipped : Dead mode selected

Backup enabled, Will read Certificates now...
Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info :
CMT ASICID : 000000010000022600010006010C192101001101
CMT EM0 ID : 00000232
CMT EM1 ID : 00000353
CMT PUB ID : 19E000193C267E565B012E4A9ED7115EE71B8D77
CMT MODE ID : 00
CMT R_HASH : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID : 191EC665DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg
CMT Loader sent, Boot Ok
MCU Configuration
FLASHID : 220800EC , CMT , NOR
CMT Flash ID : 220800EC < SAMSUNG [SEC] => K8F5615ETM\K5G5629ATD
FLCNT : 000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo.fg
CMT Algo sent
PAPUBkeys blank (erased or HW failure)
Transmission mode : Dual (Ddr, TX2)

Boot Done!

CMT : Read NPC certificate...
Cert size : 0 byte(s)
CMT : Read CCC certificate...
Cert size : 0 byte(s)
CMT : Read HWC certificate...
Cert size : 0 byte(s)
CMT : Read VARIANT certificate...
Cert size : 0 byte(s)
No any CRT data (MCU damaged/CERT erased), skip saving

Init Service mode... Wait...

Init Service Mode Failed!
Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info :
CMT ASICID : 000000010000022600010006010C192101001101
CMT EM0 ID : 00000232
CMT EM1 ID : 00000353
CMT PUB ID : 19E000193C267E565B012E4A9ED7115EE71B8D77
CMT MODE ID : 00
CMT R_HASH : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID : 191EC665DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg
CMT Loader sent, Boot Ok
MCU Configuration
FLASHID : 220800EC , CMT , NOR
CMT Flash ID : 220800EC < SAMSUNG [SEC] => K8F5615ETM\K5G5629ATD
FLCNT : 000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo.fg
CMT Algo sent
PAPUBkeys blank (erased or HW failure)
Transmission mode : Dual (Ddr, TX2)

Boot Done!

Transmission mode : Dual (Ddr, TX2)
Erase : Processing rm217__07.21.mcusw
Found 9 areas to erase, erase group
Asic : CMT , Sub : NOR
CMT , NOR , Area : 0x00000000 - 0x000006BF
CMT , NOR , Area : 0x000006C0 - 0x0001FFFF
CMT , NOR , Area : 0x00020000 - 0x0007FFFF
CMT , NOR , Area : 0x00080000 - 0x000DFFFF
CMT , NOR , Area : 0x00100000 - 0x001FFFFF
CMT , NOR , Area : 0x00200000 - 0x0031FFFF
CMT , NOR , Area : 0x00320000 - 0x0105FFFF
CMT , NOR , Area : 0x01060000 - 0x01067FFF
CMT , NOR , Area : 0x01068000 - 0x0107FFFF
Using TimeOut : 5 min ( 300 sec )
Erasing, wait.....
CMT : Group erase Ok
TIME : Erase time : 00:00:16
Transmission mode : Dual (Ddr, TX2)
Write : Processing rm217__07.21.mcusw
CMT: Writing Hash CERT [NOLO]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [UPDAPP]
CMT: Writing Hash CERT [DSP0]
CMT: Writing Hash CERT [MCUSW]
CMT: Writing Hash CERT [PMM_CONF]
CMT: Writing Hash CERT [SBIF_CONF]
Total writen 943 blocks
TIME : Write time : 00:01:53


Transmission mode : Dual (Ddr, TX2)
Erase : Processing rm217__07.21.ppm_v
Found 1 areas to erase, erase group
Asic : CMT , Sub : NOR
CMT , NOR , Area : 0x01080000 - 0x015FFFFF
Using TimeOut : 5 min ( 300 sec )
Erasing, wait.....
CMT : Group erase Ok
TIME : Erase time : 00:00:15
Transmission mode : Dual (Ddr, TX2)
Write : Processing rm217__07.21.ppm_v
Total writen 330 blocks
TIME : Write time : 00:00:40


ConvertImage: Processing rm217__07.21.image_v_black
ConvertImage: Page Size is 64K, converting...
ConvertImage: File converted
Transmission mode : Dual (Ddr, TX2)
Erase : Processing rm217__07.21.image_v_black_128
Found 1 areas to erase, erase group
Asic : CMT , Sub : NOR
CMT , NOR , Area : 0x01600000 - 0x01FDFFFF
Using TimeOut : 5 min ( 300 sec )
Erasing, wait.....
CMT : Group erase Ok
TIME : Erase time : 00:00:27
Transmission mode : Dual (Ddr, TX2)
Write : Processing rm217__07.21.image_v_black_128
Total writen 320 blocks
TIME : Write time : 00:00:38


Init Service mode... Wait...

Init Service mode Failed! Skip AfterFlash
Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok

[IMG][/IMG]

[quanghuy1990]

vào seting chọn kết nối ufs rồi check chon file chạy như giao diên box khac thôi

[thuy1986]

vào seting chọn kết nối ufs rồi check chon file chạy như giao diên box khac thôi

cái này có chạy usb được không các pro

[THIÊN UY™]

cái này có chạy usb được không các pro

cái này chạy =usb cũng ok.

[VanTuan-ST]

Chắc bị fire dongle trả đũa đây mà.

[tamquyen]

buồn ghê mới sắm em nó được có mấy ngày