Update cyclonebox anh em vui long post ở đây nhé

[TUYHOAGSM™]

Hi,
just a server update for new loaders
Supported
- Unlock by code calculation
- Superdongle repair/rebuild
- Standlone SX4 authorization
- DEVLOCk extract
- ..

Small "Taste "

WARNING: "1BB0020A296303443292389F545846C201100A5C.C000381B " Not Exists, Will read it...
Reading CYC file from phone...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102011104
CMT_EM_ASIC_ID: 00001040
CMT_EM_ASIC_ID: 00001030
CMT_PUBLIC_ID: 1BB0020A296303443292389F545846C201100A5C
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC: 3E273BF6
CMT_SECURE_ROM_CRC: 37BE26FA
CMT Ready!
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 0.1.37.1, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
Exploiting - running preloader...
R&D: Skip Preloader Crypt
Preloader running OK, Running Custom Loader...
Custom loader running OK! Working...
New Loader Detected
Loader: RAPUYama Loader v1.01 (c) KarwosSoft 2010 Poland
Loader: Running PA_HACK...
PA_HACK: OK, reading Die ID...
PA_HACK: Done
1BB0020A296303443292389F545846C201100A5C.C000381B Saved OK!

Thanks

[HoangThong_hotrokythuat3]

*** Cyclone Box - Download - Installation - First Steps ***

--------------------------------------------------------------------------------

(Updated 07.07.2010 - )


1. Download final installer from: http://www.cyclonebox.com/downloads/...xInstaller.exe and Install it. While installing agree to install box drivers, etc.

2. Connect box to PC. PC should detect new device - "Cyclone Bootloader". Simply do automatic driver installation, till installer installed them in Win32 INF already.

3. Run Start -> Programs -> Cyclone Box -> Cyclone Box



At bottom, you should see "Connected [Bootloader Mode]". That means your box was detected by software, and you can proceed with box registration - needed step to activate your box.

4. Run Box Registration Wizard, click Prepare Box.



Select your reseller from list, and fill all needed data.



If you see "Box registration status: Registered OK" that means all passed ok. You can proceed with box activation.

5. Run Box Maintenance Wizard, and click Maintenance box. In 1-2 minutes your box will be initialized.

**** VERY IMPORTANT : During box upgrade, please DON'T disconnect your box, even if software may act as hang ! We use ciphering on few layers during upgrade, and if you have slower PC, decrypting RSA and other ciphers, may take quite more time !! And then, if you disconnect your box, it will not be upgraded. It is no problem, because it will not be damaged, but You will lose YOUR time and OURS time, asking for next update credit !!



6. Your box is registered and activated. Now your security card needs be initialized. To initialize security card, box needs be activated! Run Security Card Manager. Read your card, and click Fill Credits. Box should change its mode to Cyclone Box and Windows should install new drivers again (same steps as for Bootloader). On bottom of screen you should see "Connected [Main Mode]".

How to activate Super DCT4 in my box?
It is very simple. Go to "Credits" module (same as you are using for calculating ASK/RPL), and click big "Activate SUPER DCT4" button. In seconds you should see similiar message:

Started Super DCT4 Activation at 03:45:20
Handling device: [Cyclone Team], [Cyclone Box]
Service Tag: 4F67674F5428157448CEACEB547BC575
Cyclone Server (1.0.0.483), Cyclone Box Team 2008, 2009 - Ready.

Super DCT4 Activated Successfully! Credits Left: 950
Please, replug your box from USB now, and use Maintenance Function to upgrade it again.
After next upgrade, box will be activated for Super DCT4 Functions!

As message says, replug your box and re-upgrade it again. After re-upgrade your box is SUPER-DCT4-READY




8. All is done. You can run DCT4/WD2/BB5 tool and check if necessary selftests will be passsed, so you can enjoy using your Cyclone Box One note: security card having 1000 credits at initialization. Each card operation tooks those credits, so after some time you need to reinitialize card (when counter reachs 0). This operation is of course free and realtime, using server.

Code:
Nokia DCT4/WD2/BB5 Service Tool Initialization Started, Engine Revision: 1.0.0.9912
Handling device: [Cyclone Team], [Cyclone Box]
Initializing box...
Box Firmware: Cyclone Nokia Application v01.45, (Jul 6 2010 19:20:51, gcc v4.3.2, RTOS V6.0.1), Type: Signed Production Application, (C) KarwosSoft 2010 wk27
Box Serial Number: C0000005
HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2008, wk32
Initializing security card...
Card Serial Number: D0000001
Card Firmware Revision: 0108
Card is activated
Box is activated
Started box selftests procedure
USB Voltage 4,99v PASSED
MCU Voltage 3,30v PASSED
Core Voltage 1,79v PASSED
VBAT Voltage 0,01v PASSED
VBAT Voltage 4,73v PASSED
Box VPP disabled
VPP Voltage 0,02v PASSED
Internal Box VPP Enabled
VPP Voltage 4,88v PASSED
Box VPP disabled
VPP Voltage 0,00v PASSED
External Box VPP Enabled
VPP Voltage 0,04v FAILED - IGNORED - Probably power supply is not connected
Box VPP disabled
All box selftests passed!
Super DCT4 Activation: TRUE
Initializing FBUS...
All initialized - Ready to work

Remember to check the Version of the software and the firmware of your Cyclone box

Enjoy your box!

Note : Mirror for installer and exe : Index of /downloads

[HoangThong_hotrokythuat3]

Hi!
New update for Cyclone Box is Ready.

What's new?

=====================
Installer v1.09
02.08.2010
=====================

- New BB5 Loaders v10.22.00 Introduced
- SL3 Unlocking added, uses server and 60 credits/unlock, supported models:

- 2700 Classic (RM-561)
- 2730 Classic (RM-57
- 2730c-1b (RM-579)
- 2690c (RM-635)
- 3600 Slide (RM-352) v56.26 – v57.23
- 3720 Classic (RM-51
- 5130 XpressMusic (RM-495)
- 5310 XpressMusic (RM-303) v58.58 – v59.42
- 5730s (RM-465)
- 6300 (RM-217) v57.20
- 6303 Classic (RM-443)
- 6500 Slide (RM-240) v59.60
- 6500 Classic (RM-265) v59.45
- N97 (RM-505/506/507)
- N97 mini (RM-555)

- When using New Protocol flashing, software reminds about correct TX2 cable and yellow adapter
- Added Manual Mode to retrieve SL3 NCK if you dont have phone in hand (just enter IMEI when asked)
- Added "Erase NCK Codes" - this should be used when phones needs to be factory-relocked (best to use with SL3 if you want to clear entered NCK codes). Work with SL2 too. Simlock area is untouched when Relocking to factory state, and warranty will still be ok. Seems first software on market with such funcionality.
- Fixed BlackBerry calculation problems, old version never closed TCP connection after success or non-success calculation
- Firmware v1.46 Released, Added SL3 Routines
- Minor changes and bugfixes

Example SL3 unlocked by new update


Code:

BB5 Unlock Started...
MCU Version V 07.95
MCU Date 03-02-10
Product RM-495
Manufacturer (c) Nokia
IMEI 351538045311523
Mastercode 4612735731
Simlock Server SIMLOCK SERVER
Simlock Key 2600300000000000
Simlock Profile 8000000000000000
Simlock Key Cnt 0
Simlock FBUS Cnt 0
Simlock [1,1] State: CLOSED Type: MCC-MNC Data: 26003F
Connecting to Cyclone Server...
Cyclone Server (1.0.0.632), Cyclone Box Team 2008, 2009, 2010 - Ready.
Checking job status...
Code Ready, Code: #pw+966057384237461+7#
Sending code via FBUS...
NCK[7] - ACCEPTED
Code Accepted! Unlocking Finished!

Rapidshare Download LINK
Direct LINK1
Direct LINK2


NOTE
A firmware upgrade to v1.46 is needed to use this update!


CycloneBox support in Portuguese language
Visit Here


Stay tuned,
Best Regards,
Cyclone Team

[TUYHOAGSM™]

Cyclone Calculator v1.00

- Calculates Alcatel NCK/SPCK codes
- Calculates Blakcberry Engineering Code
- 100% free and standalone, no need any activations
- Box needs be attached upon software startup (in either bootloader or main mode)

- Supported Models

B331
BlueBelt
C700
C701
C707
C717
C820
C825
E101FLIP
EL03
I650
MANDARINA DUCK
MISS SIXTY
OT103
OT203
OT203A
OT203E
OT280
OT303
OT360
OT363
OT383
OT600
OT660
OT708
OT800
PLAYBOY
S215
S218
S319
S320
S321
S520
S621
S853
V570
V670
V770
VM621I

- Supported Models/Operators:

541 ADGB1
541 AEUY1
541 AGEC1
541 AHNL1
541 ALAE1
541 ALAP1
541 ALBG1
541 ALBY1
541 ALCL1
541 ALES1
541 ALEU1
541 ALFR1
541 ALGB1
541 ALGH1
541 ALGR1
541 ALHK1
541 ALIT1
541 ALKE1
541 ALKZ1
541 ALLY1
541 ALMX1
541 ALNC1
541 ALNP1
541 ALPL1
541 ALRO1
541 ALRU1
541 ALSG1
541 ALTR1
541 ALUA1
541 ALUS1
541 AVAR1
541 AVCL1
541 AVDO1
541 AVDO3
541 AVPA3
541 AVPE1
541 AVPR1
541 AVUY1
541 BBPG1
541 BYFR1
541 CECO1
541 CECO3
541 CFMK1
541 CJUS1
541 EBES1
541 EECL1
541 EECL3
541 EKES1
541 FOUS1
541 IUUS1
541 IWUS1
541 LIAR1
541 LRFR1
541 LVAR1
541 M1TE1
541 MCMA1
541 MDBE1
541 MVCO1
541 MVGT1
541 MVHN1
541 MVSV1
541 OTFA1
541 PMPT1
541 PSAR1
541 QUUS1
541 RDES1
541 RGCH1
541 RGDO3
541 RGES1
541 RGFA1
541 RGFR1
541 RGGB1
541 RGRE1
541 RGRO1
541 RGSN1
541 RGTE1
541 RGTE2
541 RGTE5
541 SDUS1
541 SFRE1
541 SVRU1
541 TBNL1
541 TGMX1
541 TGMX3
541 TLAR1
541 TLAR3
541 TLCL3
541 TLCO3
541 TLES1
541 TLGT3
541 TLMX1
541 TLMX3
541 TLNI1
541 TLSV3
541 TLUY1
541 TLVE3
541 TWGB1
541 UCUS1
541 UUUS1
541 UVUS1
541 VDAU1
541 VDCY1
541 VDDE1
541 VDES1
541 VDFJ1
541 VDGB1
541 VDGH1
541 VDGR1
541 VDHU1
541 VDIE1
541 VDIT1
541 VDLU1
541 VDMK1
541 VDMT1
541 VDMY1
541 VDNL1
541 VDNZ1
541 VDPT1
541 VDPT2
541 VDRO1
541 VGFR1
541 VMVE1
541 VMVE3
541 WCDO1
541 ZAGA1
B331 VDAU1
B331 VDES1
B331 VDHU1
B331 VDPT1
E101FLIP AEUY1
E101FLIP ALAE1
E101FLIP ALAP1
E101FLIP ALBR1
E101FLIP ALBY1
E101FLIP ALES1
E101FLIP ALEU1
E101FLIP ALFR1
E101FLIP ALHK1
E101FLIP ALIE1
E101FLIP ALIT1
E101FLIP ALKE1
E101FLIP ALKZ1
E101FLIP ALLY1
E101FLIP ALNC1
E101FLIP ALRU1
E101FLIP ALUA1
E101FLIP AVDO3
E101FLIP AVPA3
E101FLIP AVPE1
E101FLIP AVUY1
E101FLIP CECO3
E101FLIP CFMK1
E101FLIP EBES1
E101FLIP EKES1
E101FLIP LIAR1
E101FLIP LVAR1
E101FLIP MVHN1
E101FLIP PGIT1
E101FLIP PSAR1
E101FLIP RGTE5
E101FLIP SFRE1
E101FLIP SVRU1
E101FLIP TBGB1
E101FLIP TGMX1
E101FLIP TLCO3
E101FLIP TLMX1
E101FLIP TLMX3
E101FLIP TLUY1
E101FLIP TLUY3
E101FLIP UCUS1
E101FLIP VMVE1
E101FLIP VMVE3
E101FLIP WCDO1
I650 AVCL1
I650 CECO1
I650 EECL1
I650 EKES1
I650 KPNL1
I650 MVSVA
I650 OTFA1
I650 RGDO1
I650 RGFA1
I650 RGMU1
I650 SFRE1
I650 T1MG1
I650 TBHU1
I650 TFNL1
I650 TGMX1
I650 TLMX1
I650 TLPEA
I650 TLPEB
I650 TLVE1
I650 TMPT1
I650 VDFJ1
I650 VDHU1
I650 VDPT1
I650 VMVE1
I650 VOPY1
OT103 ALBE1
OT103 ALES1
OT103 ALEU1
OT103 ALFR1
OT103 ALIE1
OT103 ALIT1
OT103 ALKE1
OT103 ALMX1
OT103 ALNL1
OT103 ALRO1
OT103 ALRU1
OT103 ALUA1
OT103 AVDO1
OT103 AVDO3
OT103 AVDO4
OT103 BBPG1
OT103 DCHT1
OT103 FOIL1
OT103 ICCR1
OT103 M1CI1
OT103 M1TE1
OT103 MVGT1
OT103 MVHN1
OT103 OTFA1
OT103 RGDO4
OT103 RGDO9
OT103 RGGQ1
OT103 RGTE1
OT103 RGTE2
OT103 RGTE5
OT103 T2CV1
OT103 TGMX1
OT103 TLMX1
OT103 TLMX3
OT103 TLPE3
OT103 TMCV1
OT103 TMST1
OT103 TTTP1
OT103 WCDO1
OT203 AFCO3
OT203 AHNL1
OT203 ALAE1
OT203 ALAP1
OT203 ALAR1
OT203 ALBG1
OT203 ALBY1
OT203 ALCY1
OT203 ALEU1
OT203 ALFR1
OT203 ALGR1
OT203 ALHI1
OT203 ALKE1
OT203 ALKZ1
OT203 ALMX1
OT203 ALNL1
OT203 ALRO1
OT203 ALRU1
OT203 ALUA1
OT203 AVAR3
OT203 AVDO3
OT203 AVDO4
OT203 AVPA3
OT203 AVPE1
OT203 AVUY1
OT203 BBPG1
OT203 CECO3
OT203 CFMK1
OT203 EECL1
OT203 EECL3
OT203 HBMY1
OT203 ICCR1
OT203 MVHN1
OT203 MVSV1
OT203 OAIL1
OT203 PAHU1
OT203 PCEC1
OT203 PCEC3
OT203 RGCM1
OT203 RGDO4
OT203 RGDO9
OT203 RGFA1
OT203 RGMU1
OT203 RGTE1
OT203 RGTE2
OT203 RGTE5
OT203 RGTE8
OT203 SFRE1
OT203 T2CV1
OT203 TBHU1
OT203 TLCO3
OT203 TLGT3
OT203 TLMX1
OT203 TLMX3
OT203 TLPA3
OT203 TLPE3
OT203 TLSV3
OT203 TLVE3
OT203 TZTN1
OT203 VDFJ1
OT203 WCDO1
OT203 WEIL1
OT203 WNIT1
OT203 ZAGH1
OT203A AFCO3
OT203A AHNL1
OT203A ALAE1
OT203A ALAP1
OT203A ALAR1
OT203A ALBG1
OT203A ALBY1
OT203A ALCY1
OT203A ALEU1
OT203A ALFR1
OT203A ALGR1
OT203A ALHI1
OT203A ALKE1
OT203A ALKZ1
OT203A ALMX1
OT203A ALNL1
OT203A ALRO1
OT203A ALRU1
OT203A ALUA1
OT203A AVAR3
OT203A AVDO3
OT203A AVDO4
OT203A AVPA3
OT203A AVPE1
OT203A AVUY1
OT203A BBPG1
OT203A CECO3
OT203A CFMK1
OT203A EECL1
OT203A EECL3
OT203A HBMY1
OT203A ICCR1
OT203A MVHN1
OT203A MVSV1
OT203A OAIL1
OT203A PAHU1
OT203A PCEC1
OT203A PCEC3
OT203A RGCM1
OT203A RGDO4
OT203A RGDO9
OT203A RGFA1
OT203A RGMU1
OT203A RGTE1
OT203A RGTE2
OT203A RGTE5
OT203A RGTE8
OT203A SFRE1
OT203A T2CV1
OT203A TBHU1
OT203A TLCO3
OT203A TLGT3
OT203A TLMX1
OT203A TLMX3
OT203A TLPA3
OT203A TLPE3
OT203A TLSV3
OT203A TLVE3
OT203A TZTN1
OT203A VDFJ1
OT203A WCDO1
OT203A WEIL1
OT203A WNIT1
OT203A ZAGH1
OT203E ALFR1
OT203E ALGB1
OT203E ALIE1
OT203E ALIT1
OT203E ALPL1
OT203E CUFR1
OT203E LRFR1
OT203E MHFR1
OT203E RGGB1
OT203E VDES1
OT203E VRGB1
OT280 ALEU1
OT280 ALFR1
OT280 ALLY1
OT280 ALRU1
OT280 RGFA1
OT280 RGFR1
OT280 RGMU1
OT280 RGRE1
OT303 AEUY1
OT303 ALAE1
OT303 ALAP1
OT303 ALAR1
OT303 ALBE1
OT303 ALBG1
OT303 ALBR1
OT303 ALBY1
OT303 ALCY1
OT303 ALEU1
OT303 ALFR1
OT303 ALGB1
OT303 ALIE1
OT303 ALIN1
OT303 ALIT1
OT303 ALKE1
OT303 ALKZ1
OT303 ALLY1
OT303 ALNC1
OT303 ALNL1
OT303 ALRO1
OT303 ALRU1
OT303 ALTR1
OT303 AVCL1
OT303 AVDO1
OT303 AVDO3
OT303 AVPA1
OT303 AVPA3
OT303 BBPG1
OT303 BYFR1
OT303 CECO1
OT303 CECO3
OT303 CFMK1
OT303 CSGR1
OT303 EECL3
OT303 FOIL1
OT303 FOIL2
OT303 HYIL1
OT303 LIAR1
OT303 LVAR1
OT303 M1TE1
OT303 MCMA1
OT303 MSUA1
OT303 MVGT1
OT303 OTFA1
OT303 PCEC1
OT303 PCEC3
OT303 RGDO1
OT303 RGDO3
OT303 RGFA1
OT303 RGGQ1
OT303 RGMU1
OT303 RGSN1
OT303 RGTE1
OT303 RGTE2
OT303 SFFR1
OT303 SFRE1
OT303 T2CV1
OT303 TBHU1
OT303 TGMX1
OT303 TLMX1
OT303 TLMX3
OT303 TLUY1
OT303 VAVN1
OT303 VDFJ1
OT303 VMVE1
OT303 WCDO1
OT303 WNIT1
OT303 WRCB1
OT303 WYIL1
OT360 AVPE1
OT360 CECO3
OT360 LIAR1
OT360 LVAR1
OT360 TLUY1
OT360 TLVE1
OT360 WCDO1
OT363 ALAE1
OT363 ALAP1
OT363 ALBR1
OT363 ALBY1
OT363 ALCY1
OT363 ALES1
OT363 ALEU0
OT363 ALEU1
OT363 ALFR1
OT363 ALGB1
OT363 ALGR1
OT363 ALKZ1
OT363 ALNC1
OT363 ALPL1
OT363 ALRO1
OT363 ALRU1
OT363 ALUA1
OT363 AVDO3
OT363 BBPG1
OT363 BYFR1
OT363 CECO3
OT363 CFMK1
OT363 EECL3
OT363 EKES1
OT363 KPNL1
OT363 MVGT1
OT363 MVHN1
OT363 MVSV1
OT363 OTFA1
OT363 RGCH1
OT363 RGDO1
OT363 RGDO3
OT363 RGES1
OT363 RGFA1
OT363 RGFR1
OT363 RGGB1
OT363 RGMD1
OT363 RGPL1
OT363 RGRE1
OT363 RGRO1
OT363 RGTE1
OT363 RGTE2
OT363 RGTE5
OT363 TIIT1
OT363 TLES1
OT363 TLMX1
OT363 TLMX3
OT363 TLUY1
OT363 UUUS1
OT363 VAVN1
OT363 VDES1
OT363 VDFJ1
OT363 WCDO1
OT383 AEUY1
OT383 ALAE1
OT383 ALEU1
OT383 ALFR1
OT383 ALGR1
OT383 ALNC1
OT383 ALRU1
OT383 ALUA1
OT383 CECO3
OT383 OTFA1
OT383 RGFA1
OT383 RGTE1
OT383 RGTE2
OT383 RGTE5
OT383 TGMX1
OT383 TGMX3
OT383 TLMX1
OT383 TLMX3
OT383 TLVE1
OT383 TLVE3
OT383 VDFJ1
OT600 AEUY1
OT600 AGEC1
OT600 ALAP1
OT600 ALCY1
OT600 ALDE1
OT600 ALEU1
OT600 ALHK1
OT600 ALLY1
OT600 ALNL1
OT600 ALUA1
OT600 AVCL1
OT600 AVDO3
OT600 AVPE1
OT600 CECO3
OT600 CFMK1
OT600 CSGR1
OT600 MVHN1
OT600 OTFA1
OT600 RGDO3
OT600 RGFA1
OT600 RGTE1
OT600 RGTE2
OT600 TBHU1
OT600 TIVE1
OT600 TLCL3
OT600 TLMX1
OT600 TLMX3
OT600 VRGB1
OT600 WCDO1
OT660 AEUY1
OT660 ALAE1
OT660 ALAP1
OT660 ALBR1
OT660 ALBY1
OT660 ALES1
OT660 ALEU1
OT660 ALFR1
OT660 ALHK1
OT660 ALIE1
OT660 ALIT1
OT660 ALKE1
OT660 ALKZ1
OT660 ALLY1
OT660 ALNC1
OT660 ALRU1
OT660 ALUA1
OT660 AVDO3
OT660 AVPA3
OT660 AVPE1
OT660 AVUY1
OT660 CECO3
OT660 CFMK1
OT660 EBES1
OT660 EKES1
OT660 LIAR1
OT660 LVAR1
OT660 MVHN1
OT660 PGIT1
OT660 PSAR1
OT660 RGTE5
OT660 SFRE1
OT660 SVRU1
OT660 TBGB1
OT660 TGMX1
OT660 TLCO3
OT660 TLMX1
OT660 TLMX3
OT660 TLUY1
OT660 TLUY3
OT660 UCUS1
OT660 VMVE1
OT660 VMVE3
OT660 WCDO1
OT708 ADGB1
OT708 AEUY1
OT708 AGEC1
OT708 AHNL1
OT708 ALAE1
OT708 ALAP1
OT708 ALBG1
OT708 ALBY1
OT708 ALCL1
OT708 ALES1
OT708 ALEU1
OT708 ALFR1
OT708 ALGB1
OT708 ALGH1
OT708 ALGR1
OT708 ALHK1
OT708 ALIT1
OT708 ALKE1
OT708 ALKZ1
OT708 ALLY1
OT708 ALMX1
OT708 ALNC1
OT708 ALNP1
OT708 ALPL1
OT708 ALRO1
OT708 ALRU1
OT708 ALSG1
OT708 ALTR1
OT708 ALUA1
OT708 ALUS1
OT708 AVAR1
OT708 AVCL1
OT708 AVDO1
OT708 AVDO3
OT708 AVPA3
OT708 AVPE1
OT708 AVPR1
OT708 AVUY1
OT708 BBPG1
OT708 BYFR1
OT708 CECO1
OT708 CECO3
OT708 CFMK1
OT708 CJUS1
OT708 EBES1
OT708 EECL1
OT708 EECL3
OT708 EKES1
OT708 FOUS1
OT708 IUUS1
OT708 IWUS1
OT708 LIAR1
OT708 LRFR1
OT708 LVAR1
OT708 M1TE1
OT708 MCMA1
OT708 MDBE1
OT708 MVCO1
OT708 MVGT1
OT708 MVHN1
OT708 MVSV1
OT708 OTFA1
OT708 PMPT1
OT708 PSAR1
OT708 QUUS1
OT708 RDES1
OT708 RGCH1
OT708 RGDO3
OT708 RGES1
OT708 RGFA1
OT708 RGFR1
OT708 RGGB1
OT708 RGRE1
OT708 RGRO1
OT708 RGSN1
OT708 RGTE1
OT708 RGTE2
OT708 RGTE5
OT708 SDUS1
OT708 SFRE1
OT708 SVRU1
OT708 TBNL1
OT708 TGMX1
OT708 TGMX3
OT708 TLAR1
OT708 TLAR3
OT708 TLCL3
OT708 TLCO3
OT708 TLES1
OT708 TLGT3
OT708 TLMX1
OT708 TLMX3
OT708 TLNI1
OT708 TLSV3
OT708 TLUY1
OT708 TLVE3
OT708 TWGB1
OT708 UCUS1
OT708 UUUS1
OT708 UVUS1
OT708 VDAU1
OT708 VDCY1
OT708 VDDE1
OT708 VDES1
OT708 VDFJ1
OT708 VDGB1
OT708 VDGH1
OT708 VDGR1
OT708 VDHU1
OT708 VDIE1
OT708 VDIT1
OT708 VDLU1
OT708 VDMK1
OT708 VDMT1
OT708 VDMY1
OT708 VDNL1
OT708 VDNZ1
OT708 VDPT1
OT708 VDPT2
OT708 VDRO1
OT708 VGFR1
OT708 VMVE1
OT708 VMVE3
OT708 WCDO1
OT708 ZAGA1
OT800 AEUY1
OT800 AGECA
OT800 ALAE1
OT800 ALAP1
OT800 ALAT1
OT800 ALBR1
OT800 ALCN1
OT800 ALCN2
OT800 ALDE1
OT800 ALES1
OT800 ALEU1
OT800 ALEU2
OT800 ALFR1
OT800 ALGB1
OT800 ALGH1
OT800 ALGR1
OT800 ALHK1
OT800 ALHU1
OT800 ALIT1
OT800 ALLY1
OT800 ALNC1
OT800 ALNL1
OT800 ALPL1
OT800 ALRS1
OT800 ALRU1
OT800 ALUA1
OT800 ALUS1
OT800 ALUSH
OT800 AVAR1
OT800 AVCL1
OT800 AVPE1
OT800 AVPR1
OT800 AVPY1
OT800 AVUY1
OT800 BBPG1
OT800 BOCN1
OT800 BTIT1
OT800 BYFR1
OT800 CFMK1
OT800 CJUS1
OT800 CJUSH
OT800 CUFR1
OT800 DWUS1
OT800 EECL3
OT800 EKES1
OT800 ERPL1
OT800 FOUS1
OT800 GUUS1
OT800 HBMY1
OT800 ICCR1
OT800 IUUS1
OT800 IUUSH
OT800 IWUS1
OT800 JCAU1
OT800 KPNL1
OT800 LIAR1
OT800 MDBE1
OT800 MVGT1
OT800 MVGTA
OT800 MVHN1
OT800 MVSV1
OT800 OCUS1
OT800 OTFA1
OT800 PCEC1
OT800 PCEC3
OT800 QUUS1
OT800 RCUS1
OT800 RGFA1
OT800 RGFR1
OT800 RGMG1
OT800 RGMU1
OT800 RGRE1
OT800 RGRO1
OT800 RGSN1
OT800 RGTE2
OT800 RGTE5
OT800 SDUS1
OT800 SFFR1
OT800 SXIN1
OT800 SYUS1
OT800 TBCZ1
OT800 TBEU1
OT800 TBGB1
OT800 TBHU1
OT800 TBMK1
OT800 TBNL1
OT800 TGMX1
OT800 TGMX3
OT800 TIIT1
OT800 TIVE1
OT800 TLAR1
OT800 TLARB
OT800 TLCLB
OT800 TLCOB
OT800 TLECB
OT800 TLGT3
OT800 TLMX1
OT800 TLMXA
OT800 TLPEB
OT800 TLSVB
OT800 TLUY1
OT800 TLUYB
OT800 TLVEB
OT800 TWGB1
OT800 UCUS1
OT800 UUUS1
OT800 UVUS1
OT800 VAVN1
OT800 VDFJ1
OT800 VDLU1
OT800 VDPT1
OT800 VLUS1
OT800 VMVE1
OT800 VMVE3
OT800 VNRS1
OT800 WCDO1
OT800 WCUS1
OT800 WCUSH
OT800 YAID1
OT800 ZAGA1
OTV570 ALAP1
OTV570 ALES1
OTV570 ALEU1
OTV570 ALFR1
OTV570 ALGR1
OTV570 ALLY1
OTV570 AVDO1
OTV570 CECO1
OTV570 RGFR1
OTV570 RGFR2
OTV570 T1MG1
OTV570 TLCL1
OTV570 TLMX1
OTV570 TZTN1
OTV570 VDFJ1
OTV570 VMVE1
OTV570 VVBG1
S621 KPNL1
S621 RGCH1
S621 RGMU1
S621 RGPL1
S621 RGRE1
S621 RGTE1
S621 T1MG1
S621 TBHR1
S621 TBMK1
S621 TLMX1
S621 VDFJ1
S621 VRGB1
VM621I AEUY1
VM621I AGEC1
VM621I ALAP1
VM621I ALCY1
VM621I ALDE1
VM621I ALEU1
VM621I ALHK1
VM621I ALLY1
VM621I ALNL1
VM621I ALUA1
VM621I AVCL1
VM621I AVDO3
VM621I AVPE1
VM621I CECO3
VM621I CFMK1
VM621I CSGR1
VM621I MVHN1
VM621I OTFA1
VM621I RGDO3
VM621I RGFA1
VM621I RGTE1
VM621I RGTE2
VM621I TBHU1
VM621I TIVE1
VM621I TLCL3
VM621I TLMX1
VM621I TLMX3
VM621I VRGB1
VM621I WCDO1

[NGUYÊNQNGAI]

Cyclone DREAM Released! FBUS2USB, TurboCache, Infineon XGold Imei, Loaders & more.

proudly presents
Cyclone Box Installer v1.10

- First in the world - Infineon XGold IMEI Backup/Restore added
- New BB5 FBUS/USB Loaders v10.34.1 introduced
- BB5 USB Flashing module rewritten, supports new Flashing Type: FUR USB - using FBUS loaders on USB. Is possible now to do also RPL write, Cert's read/write/erase, using just USB cable. Full FBUS protocol emulation over USB supported!
- FBUS2USB RAPU Support
- FBUS2USB RAP4 Support
- FBUS2USB Broadcomm Support
- Broadcomm platform flashing added (Nokia X2,....)
- 6700,E52 and other RAPunistore Booting fixed (Wrong First Char Received)
- SL3 Simlock RPL Write Introduced
- DCT4/BB5 Flash TurboCache added, increasing flashing speed a bit
- The Profile Bits is now analyzed before SL3 Unlock (it will not submit job if phone have blocked NCK unlocking - i.e. Telcel Mexico units)
- New NCK unlocking method for SL2 phones introduced (with latest MCU SW versions)
- Added Autologging (operation logs are stored in StoredFiles)
- Added USB Full RPL Backup (NPC,CCC,HWC,Simlock,WMDRM,etc)
- Added StatusBar in Nokia Tool, displaying current Task/Mobile attached
- DCC Camera Repair added for module NI00BC0000030102F201
- DCC Camera Repair added for module ISL3TI0200000C000002
- DCC Camera Repair added for module IS00TI0200000C208A03
- DCC Camera Repair added for module IS00TI02000001022B04
- DCC Camera Repair added for module 86000300010401022B04
- DCC Camera Repair added for module 8600030001040C208A03
- DCC Camera Repair added for module 86L10300010406260004
- DCC Camera Repair added for module 86L10300010406260000
- DCC Camera Repair added for module 86L103000104094C1003
- Refactorized GUI thread problems
- Improved stability of Blackberry calculator
- Improved flashing speed with Skins Enabled
- Added detailed Action Statusbar
- Added CBUS StatusBar, indicates "---->" on USB Transmit, "<----" on USB Receive, Idle and Errors
- Support area is rebuilt - file list parsing is optimized
- "Connection Closed Gracefully" in Support Area fixed
- Connection recovery in SupportArea added
- Fixed "Floating Point Divison by zero" in Support Area
- Entered NCK codes are now backed-up too upon Simlock Backup
- New progressbar introduced in Nokia Tool gui
- Improved USB SwitchToRaw
- Improved ADL Server Pooling
- Improved USB Phone Pooling
- USB BootRom detect routine rebuilt
- Fixed "Access Violation" while application exit
- Fixed Registration Tool bug when "Submit" button is not shown after Box Prepare
- Fixed bug when software after minimizing to tray don't appears at taskbar
- Added "KB Left", "Time Left", "Current Speed" real-time information while downloading files from support
- The Germany Server is now default Support Server
- Added support for Box HW Revisions B, thus is A11F, B110, B111 and B112, and other B11x
- Old "INI" File Parser Module added (for Old DCT4 phones)
- Old "INI" File parser Module added (for Old BB5 phones)
- Added support for 6630,6680,N70 ini parser (DPConverted v1-v2 VPL files)
- The product name is now resolved at Product List (i.e. RM-1 (6630))
- Auto-select flashfiles added (selects product and variants on Read Phone)
- The new method of BB5 NCK Calculation is now the default Unlock Method for BB5 mobiles. For SL3 use SL3 Online Code Calculation.
- "Abort" button added, this terminating all threads (during flash, erase, unlock, whatever)
- Skin Manager updated to v7.02, much stable and faster
- Fixed box hangup problem when PC goes to sleep mode
- During SL3 Check/Submit job, phone is readen first, then server transaction starts (to not overload server resources)
- Failed to Process Initial Challenge (2) during Bootloader Upgrade fixed
- During SL3 Submit Job software now try first to read PM 120 and detect if phone is SL3
- Small changes regarding SL3 Submit Job - should work bit smoother right now with bad cables
- Updated message about SL3 Credit consumption
- Added bigger delay between entering NCK codes (bruteforce protection)
- Fixed "Canvas does not allow drawing" while SL3 Manual Mode
- Cyclone Secure Bootloader v2.13 Released
- Cyclone Main Firmware v01.49 Released
- Cyclone Calculator v1.00 added into installer
- Cyclone USB Drivers Updated to 1.0.0.5
- Connectivity Cable drivers updated to 7.1.34.0
- Minor changes and bugfixes

How to update?
1. Uninstall old installer
2. Download new installer
3. Install it
4. Upgrade box firmware
5. Enjoy
Where from download?
http://www.karwos.hk/CycloneBoxInstaller.exe

[TUYHOAGSM™]

Hi, our server was updated, we decreased post-processing SL3 COD file time. Now, after upload COD file, you should get Level 7 code shortly after 20-30 seconds (up to 1-2 mins). I think this will help for many ppls as I see more and more COD files being uploaded every day

This is server-side update, no need to download nothing.

Stay tune

Lại 1 tin tốt lành cho USER Cyclone

[GIALAI_GSM]

Cyclone DEMOLITION! XGold1 Unlock/RPL, XGold2 Flash/RPL, W7 64bit, New log2cod, more. Installer v1.11 is Ready.

What's new ?
=====================
Installer v1.11
07.03.2011
=====================

• New BB5 FBUS/USB Loaders v10.48.1 introduced
• DCT4/BB5 Product/Variant caching added. Saves lot of time when selecting correct Datapackage. This is done automaticcly. During Deletion or Installing some of DP, cache is rebuilt automatically on user demand.
• XGold2 USB Flashing Introduced (C1-01,C1-02,C2-00,...)
• Added XGold2 RPL Backup (including CCC,HWC,NPC,Simlock) FIRST in the world. The backup is created automatically during flash.
• Added XGold2 RPL Write (CCC,HWC,NPC and Simlock) seems FIRST in the world. In order to write RPL file, you need flash your phone and add RPL file as secondary flashing Image (Add XGold2 RPL button).
• XGold2 RPL Contains FULL phone security, possible to Full restore after Flash Chip change
• Added XGold1 Unlocking by Reading LOG2COD Log file
• Added XGold1 Low-Level PM Dumping (both Secured and Nonsecured areas), seems 1st in world
• Added XGold1 Low-Level RPL Backup, seems 1st in world
• XGold1 Backed-up RPL file might be used to completly Re-Initialize phone security, i.e. after flash-chip change (RPL Contains IMEI and Simlock Block), seems 1st in world...
• Both XGold1 Low Level dumps support dead phones (phone might be dead, Cyclone will binary dump PM from flash chip directly)
• Added XGold1 Low-Level Deleted PM Keys dumping (extra option-don't write back readen PM file with deleted keys, they are ASCII marked as deleted ones). Support deleted messages, contacts, ..., seems 1st in world
• Added XGold1 FBUS/Keyboard SL Bad Entries Counter reset, seems 1st in world
• Reading XGOLD1 LOG2COD is fully standalone, seems 1st in world
• XGold1 Unlock/RPL supported mobiles: 1616, 1280, 1208, 1209, 1800, C1-00, and others...
• Added "Mapped At" FlashChip information during XGold Flashing, when possible
• Added "Sector Size" FlashChip information during XGold Flashing, when possible
• No reboot flashing for XGold added
• APE block flashing fixed for various RAPIDO mobiles
• Fixed Old Protocol (Dead) USB Flashing (RAPIDO phones: N86,etc)
• Fixed Blackberry Module upon reading MEP via USB it was placing it on wrong window
• Assigned COD files are now verified before sending to server, the auxiliary verification also takes place at Server Side
• Fixed OpenDialog filter when adding DCT4/BB5 flash file
• log2cod: v1.1 Released
• log2cod: GPU Selftests added (some GPU find bad code, or didn't find anything at all)
• log2cod: Added Ivan Golubev EULA
• log2cod: Added Queue managment
• log2cod: Code Verification added after successfull calculation
• log2cod: Console is cleared after some salts processed in order to avoid overflow
• log2cod: PeekNamedPipe() problem fixed
• log2cod: Added queue processing in loop mode (you can add new jobs during calculation)
• The transaction bar have been a bit resized
• Cyclone Box HW Rev B11x, C11x added
• Models.ini updated
• Box USB Drivers updated to v1.0.0.6 they are digitally signed now, no more problems on Win7 / Win Vista x64
• COM Emulation Service Driver updated to v1.0.0.1 it is digitally signed now, no more problems on Win7 / Win Vista x64
• Main Software is now Digitally Signed (Authenthicode)
• log2cod is now Digitally Signed (Auhtenthicode)
• Cyclone Calculator is now Digitally Signed (Authenthicode)
• Installer is now Digitally Signed (Auhtnethicode)
• New phones added to Virgin SX4 Database
• New phones added to Security Database (Virgin RPL)
• Box Firmware v1.53 Released
• Some minor and major changes and bugfixes
• Versions snap
• Installer v1.11
• Main x86 Application v1.0.0.11003
• x86 Memory Manager v4.76.0.179
• Native USB Drivers v1.0.0.6
• USB-COM Stack Drivers v1.0.0.1
• Onboard Secure Bootloader v2.13
• Onboard Main Nokia Application v1.53
• Onboard COM Emulation Code v1.00
• Onboard Security Card Revision v1.10
• Nokia Connectivity Cable Drivers 7.1.34.0
• BB5 USB/FPIF Single Line/FPIF DualLine v20110301
• DCT4 FPIF Single Line/USB v20100410
• DCT4 Unlock Patches DEPRECATED
• Communication Stack SSLv3-keys-06092008
• Skin Stack v7.21
• Box Firmware v1.53 is needed.

Download Links
http://www.karwos.hk/CycloneBoxInstaller.exe
http://www.siroya.org/downloads/CycloneBoxInstaller.exe
http://www.cyclonebox.com/downloads/...xInstaller.exe

ps1. yes, germany support server HDD is physsicly crashed.. it will be back in few days.. hope with noncorrupted content.
ps2. be prepared for more standalone&HOT things these days
ps3. new drivers included in this package are ONLY compatible with this new version. Don't try using them on older builds and vice versa !


IMPORTANT: You must update your box drivers to work with the new software version. To do this, after you installed the last exe, go in hardware manager and update your drivers looking for them in the folder c:\Program files\Cyclone box\Drivers. Once done, please, update your box firmware using the new software version. Failing doing this step will mean getting this error

Box Maintenance procedure started at 16:24:27
Box Open Error -> Security problem #5
Box Maintenance Error -> No connection was established, or box is not in needed mode

[GIALAI_GSM]

Cyclone Box v1.57 1st in world ORIGINAL RPL BACKUP and SD BACKUP for RAPU/RAP4/RAPID
Hi, new firmware for Cyclonebox is Avaiable.

- Added PM308 decryption for NEW phones (RAPU , RAP3Gv4, RAPIDO New ), that means you can:
- Superdongle Key backup
- CMLA Key backup
- Correct Phone Security Analysis for this phones
- Correct MCU/DSP timestamps analysis
- Phone auhtorization without corrupting SD key, when SD key is correct
- After local SX4 auth , phone STILL MIGHT BE authorized with ORIGINAL NOKIA SX4 CARD
- Created RPL from RAPU/RAP4 phones are now 100% like delivered from Nokia! That means after full erase and writing back backed-up RPL, your phone STILL MIGHT BE AUTHORIZED WITH ORIGINAL SX4 CARD - no security issues !
- Created RPL from RAPU phones might also SAVE PHONE from DESTROYING by some other tools (Contact Service after upgrade to latest versions...)
- Minor changes and bugfixes

This is firmware-side update only, upgrade your box firmware to v1.57 and use latest installer v1.12


Created RPL with FULL NOKIA CONTENT (SD, CMLA, ...)

RPL Creation started...
Processing CMT Part...
Storing Product Code...
Storing PSN...
Storing HWID...
Trying to store Simlock...
Reading Configuration Key...
Hashing...
Reading SHA1-RSA Signature...
Reading SHA1-HMAC Signature...
Storing Simlock...
Trying to store WMDRM RPL...
Reading Keys...
Storing WMDRM PD...
Reading Security Block...
Security block OK and saved to "RM-469_355216039314532_2011-03-10_130535.SecurityBlock.PM"
"1BB0020A296303443292389F545846C201100A5C.C000 3160 " Exists, That is good...
Storing Additional Data...
Checking Superdongle Key...
Encrypting Superdongle Key...
Storing Superdongle Key...
Checking CMLA Key...
Storing CMLA Key...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102011104
CMT_EM_ASIC_ID: 00001040
CMT_EM_ASIC_ID: 00001030
CMT_PUBLIC_ID: 1BB0020A296303443292389F545846C201100A5C
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC: 3E273BF6
CMT_SECURE_ROM_CRC: 37BE26FA
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.10.48.1, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0020004000000031, ST, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x0020004000000031, ST, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00200040 (ST), Size: 256MBytes, VPP: Not Supported
FlashChip 0x00200040 (ST), Size: 256MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.10.48.1, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 85F252E351E225CAFC4DFBC8041EABD2823E3500
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
Storing NPC...
Storing CCC...
Storing HWC...
CMT VARIANT Not Found
Restarting MCU...
RPL Saved OK

Example seccurity analysis, timestamp analysis, etc for RAPU

Started Reading MCU & DSP Timestamps...
MCU Version V ICPR82_09w46.8
MCU Date 30-03-10
Product RM-469 (Nokia E52)
Manufacturer (c) Nokia
IMEI 355216039314532
Mastercode 2637612627
Reading Security Block...
Security block OK and saved to "RM-469_355216039314532_2011-03-10_130314.SecurityBlock.PM"
"1BB0020A296303443292389F545846C201100A5C.C000 3160 " Exists, That is good...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102011104
CMT_EM_ASIC_ID: 00001040
CMT_EM_ASIC_ID: 00001030
CMT_PUBLIC_ID: 1BB0020A296303443292389F545846C201100A5C
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC: 3E273BF6
CMT_SECURE_ROM_CRC: 37BE26FA
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.10.48.1, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0020004000000031, ST, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x0020004000000031, ST, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00200040 (ST), Size: 256MBytes, VPP: Not Supported
FlashChip 0x00200040 (ST), Size: 256MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.10.48.1, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 85F252E351E225CAFC4DFBC8041EABD2823E3500
APE Boot skipped on user request
Flashbus Write baud set to 5.0Mbits
Reading MCUSW...
Reading DSP0...
Restarting MCU...
------ SECURITY BLOCK TIMESTAMPS ------
Timestamp Slots Detected: 4
Timestamp[1] "AENO", 2010-02-19 11:11:38
Timestamp[1] Hash "0BCD489612D4A4968B4D42A5631FC85C5D7E0E81"
Timestamp[1] Factory MCUSW Timestamp 1970-01-01 02:00:00
Timestamp[1] Dejan Hack Detected
Timestamp[1] ValidAfter Factory MCUSW Test Passed OK!
Timestamp[2] "CMCU", 2010-04-02 11:57:08
Timestamp[2] Hash "4CC50641D7C45E9DFE2967D4802C8710547BF54A"
Timestamp[2] Factory MCUSW Timestamp 2009-09-02 15:18:02
Timestamp[2] ValidAfter Factory MCUSW Test Passed OK!
Timestamp[3] "CDSP", 2010-04-02 11:57:07
Timestamp[3] Hash "D8C94BFA607710D856D8C78A9CE3EB411CD7AC4C"
Timestamp[3] Factory MCUSW Timestamp 2009-09-02 15:18:02
Timestamp[3] ValidAfter Factory MCUSW Test Passed OK!
Timestamp[4] "AMCU", 2010-04-02 11:57:09
Timestamp[4] Hash "BFC854388C2C26014F05B5084A8033CB30E472EB"
Timestamp[4] Factory MCUSW Timestamp 2009-09-02 15:18:02
Timestamp[4] ValidAfter Factory MCUSW Test Passed OK!
-------------------------------------
------ ACTUAL FLASH TIMESTAMPS ------
MCUSW Timestamp 2010-04-02 11:57:08
Flash MCUSW Timestamp synchronized with Security Block MCUSW Timestamp OK!
DSP Timestamp 2010-04-02 11:57:07
Flash DSP Timestamp synchronized with Security Block DSP Timestamp OK!
-------------------------------------
Finished, MCU and DSP Timestamps looks good!
Started Phone Security Analysis...
MCU Version V ICPR82_09w46.8
MCU Date 30-03-10
Product RM-469 (Nokia E52)
Manufacturer (c) Nokia
IMEI 355216039314532
Mastercode 2637612627
Reading Security Block...
Security block OK and saved to "RM-469_355216039314532_2011-03-10_130516.SecurityBlock.PM"
Step 1 : Testing SIMLOCK
SIMLOCK SEFLTEST PASSED OK!
Step 2 : Testing SECURITY
SECURITY SEFLTEST PASSED OK!
Step 3 : Analyzing Security Block
"1BB0020A296303443292389F545846C201100A5C.C000 3160 " Exists, That is good...
Checking SUPERDONGLE...
SUPERDONGLE FOUND AND CHECKSUM OK! PASSED!
Checking SIMLOCK...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking MCU&DSP TIMESTAMPS...
MCU&DSP TIMESTAMPS FOUND AND CHECKSUM OK! PASSED!
Checking CMLA KEYS...
CMLA KEYS FOUND AND CHECKSUM OK! PASSED!
Checking ECC KEYS...
ECC KEYS FOUND AND CHECKSUM OK! PASSED!
Checking DIV KEYS...
DIV KEYS FOUND AND CHECKSUM OK! PASSED!
Analyze finished!

Best Regards,
Cyclone Team

[GIALAI_GSM]

Cyclone!! FREE, STANDALONE UNLOCK/SD REPAIR/SX4 AUTH/SD BACKUP/..FOR ALL NEW BB5 HASH Hi, new update for Cyclone Box is ready.

Reading of LOG file added for all latest hashes and roms using new flashing protocol for RAPU CPU.

This means you can now:
- SP Unlock using LOG2COD
- Repair supedongle keys
- Backup superdongle key - FIRST AND ONLY IN THE WORLD (no other box support new encryption!)
- Create RPL from phone - 100% Nokia LIke (with ALL security)
- Standalone SX4 authorization without SX4 Card (only box)
- Detailed security analysis
- Read MCU&DSP Timestamps
- Others (soon....)

The new log reading method is simply not related to Root key hash.
If loader is signed for given hash and runs ok - it will work.
RAPU Loader is signed for following hashes (however most of them even not exists in production, or keys isn't use anymore, but as long as other teams provide this hashes, we will provide it too):

68597B9162BAB81AF74C56E78EA2588F
EA81B32860B86EF4231A11831045F3E6
8E309B54DA1ADDE27C2A035D63AACACD
916F75217F32081248B15C38DFC8E81B - Nokia X3-02, Nokia C5, Nokia E5, Nokia N8, Nokia C7, Nokia C3-01
DA550B5BAAB517409088A3E4F3EB53AC
46802B476C93A05CBAF76A64752086A9*
25B977A055BE9B5DEC0C38A2A279C695 -Nokia 5630, 6260s, 6700c, 6700s, 6710n, 6720c, 6730, 6750, E52, E55, E72
700370BCF8AFBAB25DD62DBD124FD9CE - Nokia 5630
87FAC992288DA497A663E5DDC0410B11
928E5FFB88D81E5F74729A212AB9D12E
F2D76DFAFD66C7F195F278417DF05888
F682624FFB08F6D955DBE7D9C0485084
55DF9CBCC80B17225043DDA1CC783C97

Off course This update is free as usual
we don't ask for any activations, we don't even require internet connection

For reading Log file you need valid TX2 enabled cable (otherwise software will hangup upon Getting Configuration!).

Here is tested with Nokia C5 (thx Moulnisky!)

Quote:
Reading SL3 LOG File...
MCU Version V ICPR82_10w08
MCU Date 26-02-10
Product RM-645 (Nokia C5)
Manufacturer (c) Nokia
IMEI 354847049967066
Mastercode 5222614247
WARNING: "0AC00114AD9C03443A69EAF6BE05ED1B1E10F214.C000 249F " Not Exists, Will read it...
Reading CYC file from phone...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102031104
CMT_EM_ASIC_ID: 00000C35
CMT_EM_ASIC_ID: 00000C30
CMT_PUBLIC_ID: 0AC00114AD9C03443A69EAF6BE05ED1B1E10F214
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 916F75217F32081248B15C38DFC8E81B
CMT_BOOT_ROM_CRC: E693EF0D
CMT_SECURE_ROM_CRC: AC22615B
CMT Ready!
New_RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.10.48.1, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0020004000000031, ST, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x0020004000000031, ST, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Loader: RAPxx CommonBoot v1.02 (C) 2011 Karwos Labs
Custom loader running OK! Working...
Readed OK, Saving to "0AC00114AD9C03443A69EAF6BE05ED1B1E10F214.C000 249F "
Success!
More will come next week probably together with new installer,bugfixes,and features....

Download Links
http://www.cyclonebox.com/downloads/...eNewUnlock.exe
http://www.karwos.hk/CycloneNewUnlock.exe
http://www.www.siroya.org/downloads/...eNewUnlock.exe

NOTE
Box Firmware v1.60 is ORDINARY for this update !

Best Regards,
Cyclone Team

Note: The hash 479 is not in the upshown list so, at the moment, the rapido with this hash are still not supported (X6, 5230 etc)

[HT_GSM™]

Hi, new update for Cyclone Box is ready.

Reading of LOG file added for all latest hashes and roms using new flashing protocol for RAPIDO CPU.

This means you can now:
- SP Unlock using LOG2COD (SL3 phones)
- Direct SP unlock of SL2 479cc.. based mobiles using NCK calculation
- Direct SP unlock of SL2 479cc.. based mobiles using RPL calculation
- Repair supedongle keys
- Create RPL from phone - 100% Nokia LIke (with ALL security)
- Standalone SX4 authorization without SX4 Card (only box)
- Detailed security analysis
- Read MCU&DSP Timestamps
- Others (soon....)

The new logreading method is simply not related to Rootkey hash.
If loader is signed for given hash and runs ok - it will work.
RAPIDO Loader is signed for following hashes (however most of them even not exists in production, or keys isn't use anymore, but as long as other teams provide this hashes, we will provide it too):

68597B9162BAB81AF74C56E78EA2588F
EA81B32860B86EF4231A11831045F3E6
8E309B54DA1ADDE27C2A035D63AACACD
916F75217F32081248B15C38DFC8E81B
DA550B5BAAB517409088A3E4F3EB53AC
B8C3ADECFC997FCD8081D3DEAF870B8C
479C6DDE3942E12C429C1D6ADED80371
C70CB07324056BC66A824347F40DB2D5
B1A9CEADB5CE9CF9FB4F442150AA8E09
46802B476C93A05CBAF76A64752086A9
1B0D74C532CA1C6133940C740E8C786E
25B977A055BE9B5DEC0C38A2A279C695
700370BCF8AFBAB25DD62DBD124FD9CE
9DDBFCFE6E73CED7D8C6268C8EB85723
7B045400E1752022F9EB80B0DEA9C65D
928E5FFB88D81E5F74729A212AB9D12E
F2D76DFAFD66C7F195F278417DF05888
CAEEBB65D3C48E6DC73B49DC5063A2EE
FCB5C510AF7F09F313D9BDE85A707CC0
9A28E119033B91D14D22838C86D0D53C
F682624FFB08F6D955DBE7D9C0485084
55DF9CBCC80B17225043DDA1CC783C97
38F312750F686F9FC9B1B3778774A195
BAF3A9C3DBFA8454937DB77F2B8852B1
A5404AE83A594ECADEE532F0C236BFA6
E9EFF4BFAA5393217CA6B17755FC3E14

Of course update is free, we don't ask for any activations, we don't even require internet connection.
For reading Log file you need valid TX2 enabled cable (otherwise software will hangup upon Getting Configuration!).

Here is tested with Nokia 5800-SL3-479cc (thx Moulnisky!)

Reading SL3 LOG File...
MCU Version V ICPR72_09w20.15
MCU Date 30-12-09
Product RM-356 (Nokia 5800 XpressMusic)
Manufacturer (c) Nokia
IMEI 352012047692891
Mastercode 413074336
WARNING: "05C00008DF1F00527E9AEF53D8B8ACEC8C185116.C0000607 " Not Exists, Will read it...
Reading CYC file from phone...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
CMT_EM_ASIC_ID: 00000296
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 05C00008DF1F00527E9AEF53D8B8ACEC8C185116
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
CMT_BOOT_ROM_CRC: 4B9B7510
CMT_SECURE_ROM_CRC: 3E691FF8
CMT Ready!
New_RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.48.1, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC004000000121, Samsung, ONENAND
Requested Algorithm: XSR 1.5 (CMT)
Sending Auxiliary Loader...
Auxiliary Loader Sent!
Loader: RAPxx CommonBoot v1.03 (C) 2011 Karwos Labs
Custom loader running OK! Working...
Readed OK, Saving to "05C00008DF1F00527E9AEF53D8B8ACEC8C185116.C0000607 "
Success!

Where from download?

http://www.karwos.hk/CycloneNewUnlockV2.exe

Box Firmware v1.60 is ORDINARY for this update !

Best Regards,
Cyclone Team