help me!

[verb276]

n1202 thay CPU chạy JAF báo:
JAF version 1.98.62
Detected PKEY: 9002DF6E
Card life counter: 64.28%
P-key nokia module version 01.02
Detected JAF INTERFACE version: 01.B1, Driver version: 40000, Library version: 30112
JAF DCT4/BB5 LOADERS DIR: C:\Program Files\ODEON\JAF\Flash\
JAF DCT4/BB5 PRODUCT DIR: C:\Program Files\Nokia\Phoenix\Products\
JAF USB LOADERS DIR: C:\Program Files\ODEON\JAF\FlashUSB\
JAF DCT3/DCTL LOADERS DIR: C:\Program Files\ODEON\JAF\Flash3\
USB Cable Driver version: 7.0.2.0
FILES SET FOR FLASHING:
MCU Flash file: NONE
PPM Flash file: NONE
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Checking path: C:\Program Files\Nokia\Phoenix\Products\RH-112\

Searching for default location of ini...
Checking path: \Products\RH-112\
Searching for JAF saved location of ini...
Checking path: C:\Program Files\Nokia\Phoenix\Products\RH-112\
Scanning ini files...
Checking path: \Products\RH-112\
Checking path: C:\Program Files\Nokia\Phoenix\Products\RH-112\
FILES SET FOR FLASHING:
MCU Flash file: C:\Program Files\Nokia\Phoenix\Products\RH-112\rh112_003.100
PPM Flash file: C:\Program Files\Nokia\Phoenix\Products\RH-112\rh112_003.10il
CNT Flash file: C:\Program Files\Nokia\Phoenix\Products\RH-112\rh1120_nai03.10il
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Backing up PM Field 208 as RPL...
Setting local mode...
Failed! Aborting!
Failed to backup imei...
MCU: C:\Program Files\Nokia\Phoenix\Products\RH-112\rh112_003.100
Booting phone...
Phone didn't answer with TX line high after UEM reset!
Causes:
1. BSI line is not connected properly in connector -> Check cable, also for 3.3k resistor in serial with bsi line.
2.UEM damaged -> replace UEM.
MCU ID: 0xCCCC
This MCU ID is not supported in chosen flash file...
Error booting phone...
anh em nào có kinh nghiệm về 1202 chỉ dùm.
thank you!!

[jerrylevu]

1. BSI line is not connected properly in connector -> Check cable, also for 3.3k resistor in serial with bsi line.
2.UEM damaged -> replace UEM.
MCU ID: 0xCCCC
This MCU ID is not supported in chosen flash file...
Error booting phone...

Kiểm tra bsi , tiếp xúc cáp .thay con uem khác đi thường như vầy là đóng không chuẩn hay con u chết rồi kiếm con khác đóng lại .

[verb276]

schematic 1202 thì k có? làm sao kiểm BSI dây anh? chỉ dùm? thank you!

[jerrylevu]

thay con UEM khác đi , còn schematic của 1202 cũng có rồi kiếm trong 4r .

[paulhung]

Quăng cái log Check lên dễ nhìn hơn bro

[verb276]

Getting MCU ID
Phone didn't answer with TX line high after UEM reset!
Causes:
1. BSI line is not connected properly in connector -> Check cable, also for 3.3k resistor in serial with bsi line.
2.UEM damaged -> replace UEM.

MCU ID: 0xCCCC
Failed! Aborting!
Done!
Phone Restarted...

[verb276]

thay con UEM khác đi , còn schematic của 1202 cũng có rồi kiếm trong 4r .

schematic 1202 có anh oi! chi co solution.

[thuyyt]

thay sai cpu roi

[verb276]

thay sai cpu roi

CPU của 1202 mà anh?

[jerrylevu]

kiếm con cpu 1200 thay vô unlock lại là ok .