RIFF BOX JTAG New Update AE Post ở đây

[ĐẶNG BẢO_GSM™]

RIFF JTAG - Direct JTAG Access to Flash Memory Plugin

16.12.2011 Direct JTAG Access to Flash Memory Plugin v1.00

Details Here:- Memory Plugin v1.00


Bug Fix updates :-

ZTE_AC2746.dll
-------------------------------------
- ID 0x100F80E1 is addedd to allowed list


Samsung_S239.dll
-------------------------------------
- ID 0x100FA0E1 is addedd to allowed list


ZTE_MF180S.dll
-------------------------------------
- ID 0x401200E1 is addedd to allowed list


Samsung_B379.dll
-------------------------------------
- ID 0x220B30E1 is addedd to allowed list


Samsung_M820.dll
-------------------------------------
- ID 0x503E00E1 is addedd to allowed list


Samsung_S5570.dll
-------------------------------------
- ID 0x503C10E1 is addedd to allowed list

[HoangThong_hotrokythuat4]

JTAG Manager 1.38
---------------------------

Added feature to disable Target ID check during resurrection

If current ID is not supported by a DLL, user can switch off ID check and still be able to try resurrection.
Though, we don't recommend it. Do it only if you are sure what you're doing and if you're sure that device
with unmatched target ID is still exactly the same model as stated in DLL.
Please note, upon JTAG Manager exe startup this option is automatically switched off.

To disable Target ID do the following:

-> Box Service -> Advanced Settings -> Tick "Ignore TARGET IDCODE . . ."


Added preset "Erase Full NAND/NOR Memory" (for this use Settings by Code button)

DCC operations presets will ensure proper use of DCC TAB features. To select DCC Operation preset, do the following:


-> DCC Read/Write TAB -> Settings By Code -> Select desired preset



Firmware 1.29
---------------------------

MPCore targets handling is improved.

Fixed bug in the ARM7 handling routines: h/w breakpoints were disabled each time any halt operation was performed

Added auxiliary instruction which improves GDB Server functionality.

[HoangThong_hotrokythuat4]

29.12.2011 Samsung Galaxy Note (GT-i9220) Unbrick – Boot Repair Supported

Samsung I9220 AP (PDA Part) is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung I9220 AP:

Solder JTAG cable to Samsung I9220 AP JTAG pads;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung I9220 AP is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

[VuongKhoaMobile]

10.01.2012 Samsung SGH-T759 Exhibit 4G Unbrick – Boot Repair supported

Added support for Samsung SGH-T759 Exhibit 4G

Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.


RIFF Box – JTAG Revolution

[HoangThong_hotrokythuat4]

10.01.2012 Samsung GT-i8150 Galaxy W (Samsung Ancora) Unbrick – Boot repair supported

Resurrecting Samsung I8150 is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Please note, MSM8255T is dual core chipset – it has ARM11 and Qualcomm Scorpion cores. During power on sequence only ARM11 core is visible on the JTAG chain. If boots are not completely damaged and it comes up to initializing of the Scorpion core then Scorpion core appears on the JTAG chain too. This will shift ARM11 from TAP0 into TAP1 position on the chain, while current resurrector has the ARM11 core hardcoded at TAP0 position. Thus make sure to establish JTAG connection in the time range while Scorpion core is not visible yet.
To resurrect Samsung I8150:

Solder JTAG cable to Samsung I8150 JTAG pads;
Make sure Samsung I8150 is selected in the list of models;
Insert battery and connect USB Data cable;
If you use only battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button.

[TuấnPhát_GSM]

HTC Inspire 4G A9192 (HTC Stallion) Unbrick, Boot, IMEI, CID, ModelID, Unlock supported

Resurrecting HTC Inspire is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Inspire boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 0.85.0024. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD9812000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Inspire:

* Solder JTAG cable to HTC Inspire JTAG pads;
* Insert batter and connect USB Data cable;
* Make sure HTC Inspire is selected in the list of models;
* If you use only battery, press Power On key;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

* Disconnect PC cable;
* Insert battery;
* Hold ‘Volume Down’ key and press ‘Power ON’ button.

[TuấnPhát_GSM]

HTC Panache/Glacier/My Touch 4G Unbrick, IMEI, CID, ModelID, Unlock supported

Resurrecting HTC Glacier is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Glacier boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM7230 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write SPL version 0.86.0000. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD1510000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Glacier:

* Solder JTAG cable to HTC Glacier JTAG pads;
* Insert batter and connect USB Data cable;
* Make sure HTC Glacier is selected in the list of models;
* If you use only battery, press Power On key;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

* Disconnect PC cable;
* Insert battery;
* Hold ‘Volume Down’ key and press ‘Power ON’ button.

_

[TuấnPhát_GSM]

09.02.2012 Samsung Galaxy Precedent SCH-M828 Unbrick supported

Samsung M828 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.
To resurrect Samsung M828 do this:

Solder JTAG cable to Samsung M828 JTAG pads;
Insert battery and connect USB cable to phone and PC;
Make sure Samsung M828 is selected in the list of models;
Click Resurrect button;
Wait few seconds until software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On to enter Download Mode;

[toilatoi142001]

14.02.2012 HTC ThunderBolt 4G ADR6400 (HTC Mecha) Unbrick – Boot repair supported

14.02.2012 HTC ThunderBolt 4G ADR6400 (HTC Mecha) Unbrick – Boot repair supported

14.02.2012 HTC ThunderBolt 4G ADR6400 (HTC Mecha) Unbrick – Boot repair supported
Resurrecting HTC Thunderbolt CP (Modem Part) part is easy.
Phone is auto powered on with USB Data Cable connected to the PC while battery is inside; sometimes during connection pressing Power On key may be required.
Please note, CP Part’s power is controlled by the AP Part, thus you may experience constant connection loses after definite ammounts of time (1-2-5-x seconds). If this keeps interferring the resurrection process, solder additionall JTAG interface cable to the AP pads, select AP resurrector DLL, go to the JTAG Read/Write page and halt AP core, then switch back to the CP JTAG interface.
To resurrect HTC Thunderbolt CP (Modem Part) Part:

Solder JTAG cable to HTC Thunderbolt CP JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC Thunderbolt CP is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
Resurrecting HTC Thunderbolt AP (PDA Part) is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.04.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG0510000’.
There is option to reflash BOOT and RECOVERY zones.
_

Bug Fix

HTC_DesireS.dll
-------------------------------------
- ID 0x27B360E1 is added to allowed list


HTC_Supersonic.dll
-------------------------------------
- added resurrection data for 4Kb NAND chips, so now DLL has data for both 4KB and 2KB versions.



Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.

RIFF Box – JTAG Revolution

[toilatoi142001]

RIFF JTAG - Samsung P6200, Huawei IDEOS S7, ZTE V9, Orange Boston, and more Some important news for today :

New updates:

• Samsung GT-P6200 Galaxy Tab 7.0 Plus Unbrick/Boot repair
  
• ZTE Light Tab (ZTE V9) Unbrick/Boot repair
• Huawei Ideos S7 Unbrick/Boot repair
• Orange Boston (Commtiva Z71) Unbrick/Boot repair
• Samsung Galaxy TAB (P1000N) Unbrick/Boot repair
• CDMA Samsung F219 Unbrick/Boot repair

Bug fixes:

• QSC1100_X14_NOR,
  
• QSC60XX_L18_D08_NOR,
  
• QSC60XX_L20_D08_NOR,
  
• QSC60XX_L24_D08_NOR

Have a nice weekend !


RIFF Box – JTAG Revolution