+ Trả lời bài viết
Trang 17 của 22 Đầu tiênĐầu tiên ... 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 CuốiCuối
Kết quả 161 tới 170 của 215
  1. #161
    Thành viên danh dự TuấnPhát_GSM's Avatar
    Ngày tham gia
    Jan 2009
    Bài viết
    1,788
    Cám ơn !!!
    117
    Thanked 452 Times in 322 Posts

    Mặc định RIFF JTAG – T-Mobile Samsung SGH-T989 Galaxy S II Unbrick – Dead Boot Repair supported, World First ! ! !

    14.03.2012 RIFF JTAG – T-Mobile Samsung SGH-T989 Galaxy S II Unbrick – Dead Boot Repair supported, World First ! ! !

    Repairing bricked Samsung T989 is easy with the RIFF Box. The device is based on the Qualcomm APQ8060 chipset.
    Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

    To resurrect Samsung T989:
    Solder JTAG cable to Samsung T989 JTAG pads;
    Connect USB cable to phone and PC;
    Insert battery;
    Make sure Samsung T989 is selected in the list of models;
    Click Resurrect button;
    Wait till software signals a successful operation completion;
    Disconnect USB cable, de-solder JTAG wires;
    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

    To enter download mode:
    Disconnect PC cable;
    Insert battery;
    Hold ‘Volume Down’ key and press Power-On.
    .

  2. #162
    Thành viên danh dự TuấnPhát_GSM's Avatar
    Ngày tham gia
    Jan 2009
    Bài viết
    1,788
    Cám ơn !!!
    117
    Thanked 452 Times in 322 Posts

    Mặc định RIFF JTAG – Samsung SGH-i727 Galaxy S II Skyrocket Unbrick – Dead Boot Repair, World First ! ! !

    14.03.2012 RIFF JTAG – Samsung SGH-i727 Galaxy S II Skyrocket Unbrick – Dead Boot Repair, World First ! ! !

    Repairing bricked Samsung I727 is easy with the RIFF Box. The device is based on the Qualcomm APQ8060 chipset.
    Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

    To resurrect Samsung I727:
    Solder JTAG cable to Samsung I727 JTAG pads;
    Connect USB cable to phone and PC;
    Insert battery;
    Make sure Samsung I727 is selected in the list of models;
    Click Resurrect button;
    Wait till software signals a successful operation completion;
    Disconnect USB cable, de-solder JTAG wires;
    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

    To enter download mode:
    Disconnect PC cable;
    Insert battery;
    Hold ‘Volume Down’ key and press Power-On.

  3. #163
    Thành viên danh dự TuấnPhát_GSM's Avatar
    Ngày tham gia
    Jan 2009
    Bài viết
    1,788
    Cám ơn !!!
    117
    Thanked 452 Times in 322 Posts

    Mặc định RIFF JTAG – HTC EVO 3D (HTC Shooter) Unbrick – Boot Repair Supported, World First ! ! !

    14.03.2012 RIFF JTAG – HTC EVO 3D (HTC Shooter) Unbrick – Boot Repair Supported, World First ! ! !

    Repairing bricked HTC EVO 3D (PG86300) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
    Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 1.49.0007. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG8630000’.
    There is option to reflash BOOT and RECOVERY zones.

    To resurrect HTC EVO 3D:
    Solder JTAG cable to HTC EVO 3D JTAG pads;
    Insert batter and connect USB Data cable;
    Make sure HTC EVO 3D is selected in the list of models;
    If you use only battery, press Power On key;
    Click Resurrect button;
    Wait till software signals a successful operation completion;
    Disconnect power supply, de-solder JTAG wires;
    Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

    To enter download mode:
    Disconnect PC cable;
    Insert battery;
    Hold ‘Volume Down’ key and press ‘Power ON’ button.
    .

  4. #164
    Thành viên danh dự TuấnPhát_GSM's Avatar
    Ngày tham gia
    Jan 2009
    Bài viết
    1,788
    Cám ơn !!!
    117
    Thanked 452 Times in 322 Posts

    Mặc định RIFF JTAG - WANTED ! ! ! HUAWEI Models ! ! !

    Hello dear RIFF Box users !

    Time to time we need help from our users, in order to improve our support and increase list of supported devices.

    In this topic I'll post wanted stuff, so users who provide help here will have priority when they need support.

    15.03.2012 Important - RIFF Box HUAWEI Phones Support

    Wanted following Huawei Models:

    * U8110 (Dead)
    * U8120 (Dead)
    * U8150(Dead)
    * U8230(Dead)
    * U8300 (Dead)
    * U8510 (Dead)
    * U8650 (Working)
    * U8800 (Working)
    * U8860 (Working)
    * Any other Huawei model


    If You have any of above mentioned models, please contact me via ICQ or Sonork for further steps.




    Dead phones needed for beta tests :

    * Samsung T589
    * LG E510
    Working phone full dumps :
    * LG E510
    Phones needed in Ukraine, Kiev :

    Any HTC Model, based on QUALCOMM MSM82xx CPU, in QHUSB_DLOAD mode (Error 0X44 on JTAG)
    List of models:

    * HTC Desire HD
    * HTC Desire S
    * HTC Desire Z
    * HTC Sensation
    * HTC Inspire
    * Any other model based on MSM8255, MSM8260



    Any Samsung model (Working or Bricked), based on QUALCOMM APQ8060 CPU

    List of models:

    * Samsung i717
    * Samsung E160S
    * Samsung E110s

    PCB Photos we need :

    * Any of not supported model !


    Photos must be made in high resolution, if possible on daylight, without use of flash or artificial light.

    Good photo sample :

  5. #165
    Support Manager ĐẶNG BẢO_GSM™'s Avatar
    Ngày tham gia
    May 2011
    Địa điểm
    Hà Nội City
    Bài viết
    3,996
    Cám ơn !!!
    1,312
    Thanked 1,725 Times in 1,148 Posts
    Long Biên Mobile Service Center - Nhận active IPhone 3s/4/4s/5 lên QT
    Yahoo: dangbao4vn - Phone : 0973 233 336

    Đặng Quốc Bảo, STK: 0541000209574 Ngân hàng Vietcombank CN Long Biên HN

  6. #166
    Thành viên danh dự TuấnPhát_GSM's Avatar
    Ngày tham gia
    Jan 2009
    Bài viết
    1,788
    Cám ơn !!!
    117
    Thanked 452 Times in 322 Posts

    Mặc định RIFF JTAG – HTC EVO View 4G Unbrick, Unlock, IMEI and CID update supported

    19.03.2012 RIFF JTAG – HTC EVO View 4G Unbrick, Unlock, IMEI and CID update supported

    Repairing bricked HTC EvoView4G is easy using RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
    Some (or all) revisions of HTC EvoView4G boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM8255 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
    Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL to 1.38.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG4120000’.
    There is option to reflash BOOT and RECOVERY zones.
    Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

    To resurrect HTC EvoView4G:
    *Solder JTAG cable to HTC EvoView4G JTAG pads;
    *Insert battery and connect USB Data cable;
    *Make sure HTC EvoView4G is selected in the list of models;
    *If you use only battery, press Power On key;
    *Click Resurrect button;
    *Wait till software signals a successful operation completion;
    *Disconnect power supply, de-solder JTAG wires;
    Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

    To enter download mode:
    *Disconnect PC cable;
    *Insert battery;
    *Hold ‘Volume Down’ key and press ‘Power ON’ button.

  7. #167
    Support Manager ĐẶNG BẢO_GSM™'s Avatar
    Ngày tham gia
    May 2011
    Địa điểm
    Hà Nội City
    Bài viết
    3,996
    Cám ơn !!!
    1,312
    Thanked 1,725 Times in 1,148 Posts

    Mặc định

    RIFF JTAG – HTC EVO View 4G Unbrick, Unlock, IMEI and CID update supported
    19.03.2012 RIFF JTAG – HTC EVO View 4G Unbrick, Unlock, IMEI and CID update supported

    GSM-Forum - View Single Post - RIFF JTAG Updates -Unbrick Samsung i9210,T989, i727, HTC Sensation WORLD FIRST ! ! !


    Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.

    RIFF Box – JTAG Revolution
    Long Biên Mobile Service Center - Nhận active IPhone 3s/4/4s/5 lên QT
    Yahoo: dangbao4vn - Phone : 0973 233 336

    Đặng Quốc Bảo, STK: 0541000209574 Ngân hàng Vietcombank CN Long Biên HN

  8. #168
    Support Manager ĐẶNG BẢO_GSM™'s Avatar
    Ngày tham gia
    May 2011
    Địa điểm
    Hà Nội City
    Bài viết
    3,996
    Cám ơn !!!
    1,312
    Thanked 1,725 Times in 1,148 Posts

    Mặc định

    RIFF JTAG - Samsung P6810, HTC Sensation XL Supported and more !
    21.03.2012 RIFF JTAG Box Updates:

    Whats new:

    Bug fixes:
    • Samsung Galaxy i9003 (3 new DLL, with adjusted I/O voltage levels)
    • SonyEricsson E15i (ROM not supported bug fixed)
    Torrent Tracker:
    Remote Helper:


    Who rules the galaxy ?


    www.jtagbox.com
    Long Biên Mobile Service Center - Nhận active IPhone 3s/4/4s/5 lên QT
    Yahoo: dangbao4vn - Phone : 0973 233 336

    Đặng Quốc Bảo, STK: 0541000209574 Ngân hàng Vietcombank CN Long Biên HN

  9. #169
    Thành viên danh dự TuấnPhát_GSM's Avatar
    Ngày tham gia
    Jan 2009
    Bài viết
    1,788
    Cám ơn !!!
    117
    Thanked 452 Times in 322 Posts

    Mặc định 27.03.2012 RIFF JTAG – Samsung SCH-I500 Galaxy S Mesmerize/Fascinate Unbrick Supported

    Repairing bricked Samsung SCH-I500 Galaxy S Mesmerize/Fascinate is easy with RIFF Box.
    I500 is based on the S5PCxxx Processor (ARM core is Cortex-A8). Please note the adaptive clocking mode (RTCK) is not available on this processor, so make sure to select a fixed TCK frequency.
    To establish the JTAG connection attach battery cable and press Power On key.
    In case after resurrection the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.

    To resurrect Samsung I500:
    Solder JTAG cable to Samsung I500 JTAG pads;
    Attach battery cable and press Power On key;
    Make sure Samsung I500 is selected in the list of models;
    Make sure a fixed TCK frequency is selected;
    Click Resurrect button;
    Wait till software signals a successful operation completion;
    Disconnect USB cable, de-solder JTAG wires;
    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

  10. #170
    Support Manager ĐẶNG BẢO_GSM™'s Avatar
    Ngày tham gia
    May 2011
    Địa điểm
    Hà Nội City
    Bài viết
    3,996
    Cám ơn !!!
    1,312
    Thanked 1,725 Times in 1,148 Posts

    Mặc định

    RIFF JTAG – Samsung SCH-i920 Omnia, Samsung SHV-E120S Galaxy Dead Boot Repair support
    RIFF JTAG – Samsung SCH-i920 Omnia II 8GB Unbrick – Dead Boot repair supported

    RIFF JTAG – Samsung SHV-E120S Galaxy S II HD LTE (Samsung Celox) Unbrick – Dead Boot Repair supported



    Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.


    RIFF Box – JTAG Revolution
    Long Biên Mobile Service Center - Nhận active IPhone 3s/4/4s/5 lên QT
    Yahoo: dangbao4vn - Phone : 0973 233 336

    Đặng Quốc Bảo, STK: 0541000209574 Ngân hàng Vietcombank CN Long Biên HN

+ Trả lời bài viết

Thread Information

Users Browsing this Thread

Hiện có 7 người đang xem bài này . Bao gồm : 0 thành viên và 7 khách

     

Similar Threads

  1. ORT-JTAG New Update AE Post ở đây
    By TuấnPhát_GSM in forum ORT-JTAG
    Trả lời: 262
    Bài viết cuối: 10-02-2015, 12:49
  2. RIFF - JTAG New update
    By thanhtunggialai™ in forum RIFFBOX
    Trả lời: 1
    Bài viết cuối: 10-08-2013, 23:35
  3. ORT-JTAG New Update AE Post ở đây
    By ĐẶNG BẢO_GSM™ in forum ORT-JTAG
    Trả lời: 0
    Bài viết cuối: 28-12-2011, 10:22
  4. Riff jtag update unlock htc hd7
    By vinhgsm_hue in forum ORT-JTAG
    Trả lời: 0
    Bài viết cuối: 18-02-2011, 08:48
  5. Trả lời: 0
    Bài viết cuối: 08-08-2010, 11:16

Quyền viết bài

  • Bạn không thể tạo chủ đề mới
  • Bạn không thể gửi trả lời
  • Bạn không thể gửi đính kèm
  • Bạn không thể sửa bài viết của bạn
Lên đầu trang
thiet bi sua chua slim sim, heicard, sim ghep Firmware android giải pháp nhà thông minh