1200 cần giúp.

[vietluan]

mình mang qua jaf flaJAF version 1.98.62
Detected PKEY: 900158CF
Card life counter: 67.86%
P-key nokia module version 01.02
Detected JAF INTERFACE version: 01.B1, Driver version: 40000, Library version: 30107
JAF DCT4/BB5 LOADERS DIR: C:\Program Files\ODEON\JAF\Flash\
JAF DCT4/BB5 PRODUCT DIR: C:\Program Files\Nokia\Phoenix\Products\
JAF USB LOADERS DIR: C:\Program Files\ODEON\JAF\FlashUSB\
JAF DCT3/DCTL LOADERS DIR: C:\Program Files\ODEON\JAF\Flash3\
USB Cable Driver version: 7.0.2.0
Changing mode...Done!
FILES SET FOR FLASHING:
MCU Flash file: NONE
PPM Flash file: NONE
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: C:\Program Files\Nokia\Phoenix\Products\1200\RH-99_dp_v_29_10_MCUSW5_51\rh99_05.510
PPM Flash file: NONE
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: C:\Program Files\Nokia\Phoenix\Products\1200\RH-99_dp_v_29_10_MCUSW5_51\rh99_05.510
PPM Flash file: C:\Program Files\Nokia\Phoenix\Products\1200\RH-99_dp_v_29_10_MCUSW5_51\rh99_05.51mr
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: C:\Program Files\Nokia\Phoenix\Products\1200\RH-99_dp_v_29_10_MCUSW5_51\rh99_05.510
PPM Flash file: C:\Program Files\Nokia\Phoenix\Products\1200\RH-99_dp_v_29_10_MCUSW5_51\rh99_05.51mr
CNT Flash file: C:\Program Files\Nokia\Phoenix\Products\1200\RH-99_dp_v_29_10_MCUSW5_51\rh990_nai5.51mr
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Backing up PM Field 208 as RPL...
Setting local mode...
Failed! Aborting!
Failed to backup imei...
MCU: C:\Program Files\Nokia\Phoenix\Products\1200\RH-99_dp_v_29_10_MCUSW5_51\rh99_05.510
Booting phone...
Phone didn't answer with TX line high after UEM reset!
Causes:
1. BSI line is not connected properly in connector -> Check cable, also for 3.3k resistor in serial with bsi line.
2.UEM damaged -> replace UEM.
MCU ID: 0xCCCC
This MCU ID is not supported in chosen flash file...
Error booting phone...sh nó báo thế này/

[shockcuteboy]

Phone didn't answer with TX line high after UEM reset!
Causes:
1. BSI line is not connected properly in connector -> Check cable, also for 3.3k resistor in serial with bsi line.
2.UEM damaged -> replace UEM.
MCU ID: 0xCCCC
This MCU ID is not supported in chosen flash file...
Error booting phone...sh nó báo thế này/[/QUOTE]

có nghĩa là:
Điện thoại không trả lời với dòng TX cao sau khi thiết lập lại UEM! Bởi vì:

BSI dòng chưa được kết nối đúng trong kết nối -> Kiểm tra cáp, có thể cho 3.3k resistor nối tiếp với bsi trong dòng.
2.UEM bị hư hỏng -> thay UEM.
MCU ID: 0xCCCC
MCU ID này không được hỗ trợ đèn flash đã chọn trong tập tin ...
Lỗi khởi động điện thoại