SmartMoto v1.19 and Smart-Clip v2.24

[Start307]

SmartMoto v1.19 & Smart-Clip v2.24
Dear users,

We are pleased to announce the release of new version of SmartMoto v1.19 and Smart-Clip v2.24

With this release we add M1000 to supported models list.

Unlock procedure for M1000

Models with boot versions up to 0.6.1.2 could be unlocked simply by pressing "Unlock" button on Smart-Clip. (standard unlock procedure for P2K models)

Boot version 0.6.1.2 needs to be unlocked via Remove RSA option.

1. Power the phone ON;
2. Connect the phone to a powered clip;
3. Launch SmartMoto;
4. Press Search button in SmartMoto;
5. Program should detect the handset;
6. Go to Unlock tab;
7. Press Remove RSA;
8. Phone enters boot mode, message "Waiting" appears on the bottom of the screen;
9. Press 1 and 2 keys simultaneously in upper part of the handset and SmartMoto will continue the process;
10. Program will show a popup window with description of procedure to follow:
* Remove phone battery
* Ensure that USB cable is plugged to the phone
* Press phone keys 1 and 2 simultaneously
* While holding Button 1 and Button 2, insert battery
* Release button 1 and 2
* Message "Waiting" should appear on the bottom of phoneТs display
* Press and release phone keys 1 and 2 simultaneously once more
* Message "Waiting" should disappear, press 'OK' to continue
11. SmartMoto finishes removing RSA, the handset turns ON;
12. Now phone requires being unlocked with Unlock button of Smart-Clip;
* Connect the phone to the powered clip
* Press UNLOCK button on the clip
* Phone reloads. Within 5-10 seconds message "Waiting" appears on the bottom of the phoneТs display
* Press 1 and 2 keys simultaneously in upper part of the handset. Message "Waiting" disappears, phone enters boot mode (if you don't press these 2 keys during message "Waiting" is displayed, the clip will give red E/G led and you will have to start with step 1 again)
* After 1 and 2 keys have been pressed E/G green led will blink and phone reboots. Meanwhile E/G will give frequent green blinking and phone will turn on.
Do not disconnect cell phone from Smart-Clip while green led indicator blinks!
* Green E/G led glows.
13. The cell phone is unlocked.


Models with higher boot version will require Testpoint procedure to be unlocked.

Please be aware that TP procedure for M1000 and data cable differs from other P2K models.

Testpoint unlock procedure for M1000

1. Disassemble the phone;
2. Connect USB-data cable;
3. Connect Testpoint A to Testpoint B;
4. Press Button 1 and Button 2 simultaneously;
5. While holding Button 1 and Button 2 insert battery;
6. Release Button 1 and Button 2 for 1 second;
7. Press and release again Button 1 and Button 2 simultaneously;
8. Press Search button in SmartMoto;
9. SmartMoto should detect УS Blank Paragon POGФ or УS Blank Rainbow POGФ;
10. Disconnect Testpoint;
11. Go to Unlock tab of SmartMoto.
12. Select required model from the list;
13. Press Unlock via Testpoint;
14. Assemble the handset, itТs ready for use.

M1000 data cable pinout


Please note. Testpoint schematics are moved to SmartMoto section at www.boot-loader.com. Use the testpoint for your specific phone model and follow the step-by-step instruction strictly. Please note that with some models there is a single contact that should be grounded, others have two contacts that should be connected to each other


If you wish to receive news on updates immediately, please subscribe to our SMS notification system.


Smart-Clip ON!



Best Regards
GSMServer team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

[nguyenms]

Thanks for info!