RIFF BOX JTAG New Update AE Post ở đây

[TuấnPhát_GSM]

08.04.2011 Samsung S7230E Wave 723 Unbrick – Boot Repair supported

Resurrecting Samsung S7230E is easy. To power the phone connect USB cable and insert battery. In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.


To resurrect Samsung S7230E:

* Solder JTAG cable to Samsung S7230E JTAG pads;
* Connect USB cable to phone and PC;
* Insert battery;
* Make sure Samsung S7230E is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state. We used MultiLoader 5.64 version.


To enter download mode:

* Disconnect PC cable;
* Insert battery;
* Hold both ‘Volume Down’ (on the left side of phone) and ‘Lock’ (right side bottom part) keys and press Power-On.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

[TuấnPhát_GSM]

21.04.2011 CDMA Motorola W150i (MSM6000) Repair supported


Resurrecting Motorola W150i is simple. Phone is auto powered on with charger connected; battery presence is not required. Pin TMODE has to be connected to GND in order to enable JTAG connection.
Please note, MSM6000 draws power from JTAG pins, thus board can be detected via JTAG even without any power supplied. But for successful resurrection the power (battery or charger) is required. Thus when resurrection is complete don’t forget to disconnect phone from RIFF BOX to de-power it completely.


To resurrect Motorola W150i:

Solder JTAG cable to Motorola W150i JTAG pads;
Connect charger for auto power on or use battery;
Make sure Motorola W150i is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


RIFF Box – JTAG Revolution

[TuấnPhát_GSM]

22.04.2011 CDMA Haier C3010, LG LSP450T Repair supported


Resurrecting Haier C3010 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chips with IDs 0x00EC/0x257E and 0x017E/0×2210. Proper data will be selected automatically depending on memory ID in your device.


To resurrect Haier C3010:

* Solder JTAG cable to Haier C3010 JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure Haier C3010 is selected in the list of models;
* Click Resurrect button;
* Choose which areas to flash;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;

Resurrecting LG LSP450T is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0×0020/0×8867


To resurrect LG LSP450T:

* Solder JTAG cable to LG LSP450T JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure LG LSP450T is selected in the list of models;
* Click Resurrect button;
* Choose which areas to flash;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

[TuấnPhát_GSM]

So, its resurrection times

Updates for today :

* RIFF JTAG – HTC 7 Trophy T8686 (HTC Spark) Unbrick, Unlock, IMEI Repair, CID Update, ModelID Repair supported « RIFF Box – JTAG Revolution
* RIFF JTAG – CDMA ZTE C370 Repair supported « RIFF Box – JTAG Revolution
* RIFF JTAG – CDMA Haier C6000 Repair supported « RIFF Box – JTAG Revolution
* RIFF JTAG – CDMA Haier C5100 Repair supported « RIFF Box – JTAG Revolution
* RIFF JTAG – CDMA Haier C2040 Repair supported « RIFF Box – JTAG Revolution

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

[TuấnPhát_GSM]

03.05.2011 Samsung B2710 (Samsung Xcover 271) Unbrick / Repair supported


Samsung B2710 resurrection is simple. Phone is auto powered on when USB Cable and battery are connected.
To resurrect Samsung B2710 do this:

* Solder JTAG cable to the Samsung B2710 JTAG pads;
* Connect USB cable to phone and PC;
* Make sure Samsung B2710 is selected in the list of models
* Click Resurrect button;
* Wait few seconds until software signals a successful operation completion;
* Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:

* Disconnect PC cable;
* Insert battery;
* Hold both ‘Volume Down’ and ’9′ keys and press Power-On. Screen lights up with Download mode message.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


RIFF Box – JTAG Revolution

[TuấnPhát_GSM]

04.05.2011 HTC Droid Incredible ADR6300 (HTC Incredible C) Unbrick Dead Boot Repair supported


Resurrecting HTC Incredible C is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB3120000′.


To resurrect HTC Incredible C:

Solder JTAG cable to HTC Incredible C JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC Incredible C is selected in the list of models;
If you use battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


To enter download mode:

Disconnect PC cable;
Insert battery;
Hold ‘Volume down’ key and press ‘Power ON’ button to enter HBoot menu;
Hold ‘Volume up’ key and press ‘Power ON’ button to enter Recovery mode;

04.05.2011 Samsung Nexus S (i9023) Unbrick Boot repair supported


Samsung I9023 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
Current resurrector has two different versions of primary boot loaders (PBL) embedded. This depends on hardware version of your phone which boot to use, thus in case of failure (cannot enter download mode after resurrection) of first loader try selecting another.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.


To resurrect Samsung I9023:

Solder JTAG cable to Samsung I9023 JTAG pads;
Connect microUSB cable to phone and PC;
Insert battery;
Make sure Samsung I9023 is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.


To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

[TuấnPhát_GSM]

07.05.2011 LG CU720 Shine Unbrick – Boot repair supported


Resurrecting LG CU720 is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.


To resurrect LG CU720:

* Solder JTAG cable to LG CU720 JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure LG CU720 is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

[TrọngTín™]

12.05.2011 Samsung Galaxy Ace S5830 Unbrick – Boot repair supported


Samsung S5830 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.


To resurrect Samsung S5830 do this:

* Solder JTAG cable to Samsung S5830 JTAG pads;
* Insert battery and connect USB cable to phone and PC;
* Make sure Samsung S5830 is selected in the list of models;
* Click Resurrect button;
* Wait few seconds until software signals a successful operation completion;
* Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.


To enter download mode:

* Disconnect PC cable;
* Insert battery;
* Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On to enter Download Mode;

12.05.2011 Huawei E5830 Broadband modem Unbrick – Boot repair supported


Resurrecting Huawei E5830 is simple. Just make sure you solder all JTAG signals. Connection can be established with USB Cable connected, though in some rare cases battery presence may be required.
If modem is not detected by RIFFBOX JTAG, disconnect JTAG connector, re-insert modem into USB and then connect back the JTAG connector.
Please note, if only an USB cable is connected the device is detected by PC as unknown device. So, after resurrection in order to check if modem is alive make sure battery is connected.


To resurrect Huawei E5830:

* Solder JTAG cable to Huawei E5830 JTAG pads;
* Insert Huawei E5830 modem into any USB port for power;
* Make sure Huawei E5830 is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;

12.05.2011 Samsung Eternity A867 Unbrick - Boot repair supported


The Samsung A867 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.


To resurrect Samsung A867:

* Solder JTAG cable to Samsung A867 JTAG pads;
* Connect USB cable;
* Make sure Samsung A867 is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


To enter download mode:

* Disconnect PC cable;
* Insert battery;
* Hold both ‘Volume Down’ and ‘Camera’ keys and press ‘Power ON’ button.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

[TUYHOAGSM™]

13.05.2011 CDMA Huawei C5589 Unbrick – Boot repair supported




Resurrecting Huawei C5589 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x017E/0×2230


To resurrect Huawei C5589:

* Solder JTAG cable to Huawei C5589 JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure Huawei C5589 is selected in the list of models;
* Click Resurrect button;
* Choose which areas to flash;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;


Dopod Magic A6188 (HTC Sapp400) Unbrick, Unlock, IMEI and CID repair supported


The HTC Magic (SAPP400) is based on ESM7206A chipset. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.53.02000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘SAPP*****’. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.


To resurrect HTC Magic (SAPP400):

* Solder JTAG cable to HTC Magic (SAPP400) JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure HTC Magic (SAPP400) is selected in the list of models;
* If you use battery, press Power On key;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


To enter download mode:

* Disconnect PC cable;
* Insert battery;
* Hold ‘Back (←)’ key and press ‘Power ON’ button. In few seconds you should see download mode saying Fastboot USB.

13.05.2011 Samsung Z630 Unbrick – Boot repair supported


Resurrection of Samsung Z630 requires battery or external power supply. Most convenient way is to use additionally an USB cable: in this case power is auto powered on and there will be no need to hold power on key during connection startup.
Please note, phone will be detected even with only USB cable connected, but stable connection and stable data exchange will be achieved only when battery (or external power supply) is connected too.


To resurrect Samsung Z630:

* Solder JTAG cable to Samsung Z630 JTAG pads;
* Insert battery (or connect external power supply to the battery pads) and connect USB cable;
* Make sure Samsung Z630 is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


To enter download mode:

* Disconnect PC cable;
* Insert battery;
* Hold ’4′ key and press ‘Power ON’ button. In few seconds you should see light-blue screen.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


RIFF Box – JTAG Revolution

[TuấnPhát_GSM]

HTC_Mozart.dll & HTC_Trophy
-------------------------------------
- Finally fixed an issure about ModelID. So ModelID is will now again be resurrected.
Those who have ModelID error just make resurrection again and all will be ok.